MC908GZ60CFJE Freescale Semiconductor, MC908GZ60CFJE Datasheet - Page 160

• Manufacturer Part Number: MC908GZ60CFJE
• Description: IC MCU 60K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ60CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

MSCAN08 Controller (MSCAN08)
12.13.5 MSCAN08 Receiver Flag Register (CRFLG)
All bits of this register are read and clear only. A flag can be cleared by writing a 1 to the corresponding
bit position. A flag can be cleared only when the condition which caused the setting is valid no more.
Writing a 0 has no effect on the flag setting. Every flag has an associated interrupt enable flag in the
CRIER register. A hard or soft reset will clear the register.
WUPIF — Wakeup Interrupt Flag
RWRNIF — Receiver Warning Interrupt Flag
TWRNIF — Transmitter Warning Interrupt Flag
RERRIF — Receiver Error Passive Interrupt Flag
1. Condition to set the flag: RWRNIF = (96 → REC) & RERRIF & TERRIF & BOFFIF
2. Condition to set the flag: TWRNIF = (96 → TEC) & RERRIF & TERRIF & BOFFIF
3. Condition to set the flag: RERRIF = (127 → REC → 255) & BOFFIF
160
If the MSCAN08 detects bus activity while in sleep mode, it sets the WUPIF flag. If not masked, a
wakeup interrupt is pending while this flag is set.
This flag is set when the MSCAN08 goes into warning status due to the receive error counter (REC)
exceeding 96 and neither one of the error interrupt flags or the bus-off interrupt flag is set
masked, an error interrupt is pending while this flag is set.
This flag is set when the MSCAN08 goes into warning status due to the transmit error counter (TEC)
exceeding 96 and neither one of the error interrupt flags or the bus-off interrupt flag is set
masked, an error interrupt is pending while this flag is set.
This flag is set when the MSCAN08 goes into error passive status due to the receive error counter
exceeding 127 and the bus-off interrupt flag is not set
while this flag is set.
1 = MSCAN08 has detected activity on the bus and requested wakeup.
0 = No wakeup interrupt has occurred.
1 = MSCAN08 has gone into receiver warning status.
0 = No receiver warning status has been reached.
1 = MSCAN08 has gone into transmitter warning status.
0 = No transmitter warning status has been reached.
1 = MSCAN08 has gone into receiver error passive status.
0 = No receiver error passive status has been reached.
Address:
Reset:
Read:
Write:
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 Data Sheet, Rev. 6
WUPIF
$0504
Bit 7
0
Figure 12-20. Receiver Flag Register (CRFLG)
RWRNIF
6
0
TWRNIF
5
0
RERRIF
4
0
(3)
TERRIF
. If not masked, an error interrupt is pending
3
0
BOFFIF
2
0
OVRIF
1
0
Freescale Semiconductor
Bit 0
RXF
0
(1)
(2)
. If not
. If not