MC908GZ60CFJE Freescale Semiconductor, MC908GZ60CFJE Datasheet - Page 239

• Manufacturer Part Number: MC908GZ60CFJE
• Description: IC MCU 60K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ60CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Chapter 16
Serial Peripheral Interface (SPI) Module
16.1 Introduction
This section describes the serial peripheral interface (SPI) module, which allows full-duplex, synchronous,
serial communications with peripheral devices.
The text that follows describes the SPI. The SPI I/O pin names are SS (slave select), SPSCK (SPI serial
clock), MOSI (master out slave in), and MISO (master in/slave out). The SPI shares four I/O pins with four
parallel I/O ports.
16.2 Features
Features of the SPI module include:
16.3 Functional Description
The SPI module allows full-duplex, synchronous, serial communication between the MCU and peripheral
devices, including other MCUs. Software can poll the SPI status flags or SPI operation can be interrupt
driven.
If a port bit is configured for input, then an internal pullup device may be enabled for that port bit.
The following paragraphs describe the operation of the SPI module. Refer to
of the SPI I/O registers.
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
•
•
Full-duplex operation
Master and slave modes
Double-buffered operation with separate transmit and receive registers
Four master mode frequencies (maximum = bus frequency ÷ 2)
Maximum slave mode frequency = bus frequency
Serial clock with programmable polarity and phase
Two separately enabled interrupts:
–
–
Mode fault error flag with CPU interrupt capability
Overflow error flag with CPU interrupt capability
Programmable wired-OR mode
I/O (input/output) port bit(s) software configurable with pullup device(s) if configured as input port
bit(s)
SPRF (SPI receiver full)
SPTE (SPI transmitter empty)
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 Data Sheet, Rev. 6
Figure 16-3
for a summary
239