MC912DG128AMPVE Freescale Semiconductor, MC912DG128AMPVE Datasheet - Page 407

• Manufacturer Part Number: MC912DG128AMPVE
• Description: IC MCU 128K FLASH 8MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC12r

Specifications of MC912DG128AMPVE

• Core Processor: CPU12
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: CAN, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: HC912D
• Core: HC12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 8
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (8-ch x 10-bit)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MC68HC912DT128A — Rev 4.0
MOTOROLA
The user should be careful that the state of the BDMACT bit is not
unintentionally changed with the WRITE_NEXT firmware command. If it
is unintentionally changed from 1 to 0, it will cause a system runaway
because it would disable the BDM firmware ROM while the CPU12 was
executing BDM firmware. The following two commands show how
BDMACT may unintentionally get changed from 1 to 0.
WRITE_X with data $FEFE
WRITE_NEXT with data $C400
The first command writes the data $FEFE to the X index register. The
second command writes the data $C4 to the $FF00 INSTRUCTION
register and also writes the data $00 to the $FF01 STATUS register.
ENTAG — Tagging Enable
SDV — Shifter Data Valid
TRACE — Asserted by the TRACE1 command
CLKSW — BDMCLK Clock Switch
BDMACT becomes set as active BDM mode is entered so that the
BDM firmware ROM is enabled and put into the map. BDMACT is
cleared by a carefully timed store instruction in the BDM firmware as
part of the exit sequence to return to user code and remove the BDM
memory from the map. This bit has 4 clock cycles write delay.
Set by the TAGGO command and cleared when BDM mode is
entered. The serial system is disabled and the tag function enabled
16 cycles after this bit is written.
Shows that valid data is in the serial interface shift register. Used by
the BDM firmware.
Freescale Semiconductor, Inc.
For More Information On This Product,
0 = BDM is not active. BDM ROM and registers are not in map.
1 = BDM is active and waiting for serial commands. BDM ROM and
0 = Tagging not enabled, or BDM active.
1 = Tagging active. BDM cannot process serial commands while
0 = No valid data. Shift operation is not complete.
1 = Valid Data. Shift operation is complete.
0 = BDM system operates with BCLK.
registers are in map
tagging is active.
Go to: www.freescale.com
Development Support
Background Debug Mode
Development Support
Technical Data
407