MC912DG128AMPVE Freescale Semiconductor, MC912DG128AMPVE Datasheet - Page 51

• Manufacturer Part Number: MC912DG128AMPVE
• Description: IC MCU 128K FLASH 8MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC12r

Specifications of MC912DG128AMPVE

• Core Processor: CPU12
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: CAN, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: HC912D
• Core: HC12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 8
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (8-ch x 10-bit)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.4.5 Nonmaskable Interrupt (XIRQ)
3.4.6 Mode Select (SMODN, MODA, and MODB)
3.4.7 Single-Wire Background Mode Pin (BKGD)
MC68HC912DT128A — Rev 4.0
MOTOROLA
The XIRQ input provides a means of requesting a nonmaskable interrupt
after reset initialization. During reset, the X bit in the condition code
register (CCR) is set and any interrupt is masked until MCU software
enables it. Because the XIRQ input is level sensitive, it can be connected
to a multiple-source wired-OR network. This pin is always an input and
can always be read. There is an active pull-up on this pin while in reset
and immediately out of reset. The pullup can be turned off by clearing
PUPE in the PUCR register. XIRQ is often used as a power loss detect
interrupt.
Whenever XIRQ or IRQ are used with multiple interrupt sources (IRQ
must be configured for level-sensitive operation if there is more than one
source of IRQ interrupt), each source must drive the interrupt input with
an open-drain type of driver to avoid contention between outputs. There
must also be an interlock mechanism at each interrupt source so that the
source holds the interrupt line low until the MCU recognizes and
acknowledges the interrupt request. If the interrupt line is held low, the
MCU will recognize another interrupt as soon as the interrupt mask bit in
the MCU is cleared (normally upon return from an interrupt).
The state of these pins during reset determine the MCU operating mode.
After reset, MODA and MODB can be configured as instruction queue
tracking signals IPIPE0 and IPIPE1 in expanded modes. MODA and
MODB have active pulldowns during reset.
The SMODN pin has an active pullup when configured as an input. The
pin can be used as BKGD or TAGHI after reset.
The BKGD pin receives and transmits serial background debugging
commands. A special self-timing protocol is used. The BKGD pin has an
active pullup when configured as an input; BKGD has no pullup control.
Refer to
Freescale Semiconductor, Inc.
For More Information On This Product,
Development
Pinout and Signal Descriptions
Go to: www.freescale.com
Support.
Pinout and Signal Descriptions
Signal Descriptions
Technical Data
51