PRIXP425ABC 885156 Intel, PRIXP425ABC 885156 Datasheet - Page 59
PRIXP425ABC 885156
Manufacturer Part Number
PRIXP425ABC 885156
Description
Manufacturer
Intel
Datasheet
1.PRIXP425ABC_885156.pdf
(96 pages)
Specifications of PRIXP425ABC 885156
Lead Free Status / Rohs Status
Supplier Unconfirmed
- Current page: 59 of 96
- Download datasheet (2Mb)
General PCB Guide—Intel
December 2007
Document Number: 252817- 008US
An example for a six-layer and eight-layer board is shown below. For stripline (signals
between planes), the stackup should be such that the signal line is closer to one of the
planes by a factor of five or more. Then the trace impedance is controlled
predominantly by the distance to the nearest plane.
the proposed stackup for the six- and eight-layer boards.
• High-speed circuits require multi-layer printed circuit boards;
• Symmetry is essential to keep the board stack-up symmetric about the center
• For best impedance control, have:
• For best noise control, route adjacent layers orthogonally. Avoid layer-to-layer
• Fabrication house must agree on design rules, including:
• The distance between the signal layer and ground (or power) should be minimized
parallelism.
to reduce the loop area enclosed by the return current
— Advantages:
— Disadvantages:
— This minimizes warping
— No more than two signal layers between every power/ground plane pair
— No more than one embedded micro-strip layer under the top/bottom layers
— Trace width, trace separation
— Drill/via sizes
— Use 0.7:1 ratio as a minimum.
• Lack of power/ground planes, resulting in unacceptable cross-talk
• Relatively high-impedance power distribution circuitry, resulting in noise on
• Controlled-impedance traces
• Low-impedance power distribution
• Higher cost
• More weight
• Manufactured by fewer vendors
®
For example: 5-mil traces, 7-mil prepreg thickness to adjacent power/ground
IXP42X product line and IXC1100 control plane processors
the power and ground rails
Intel
®
IXP42X Product Line of Network Processors and IXC1100 Control Plane Processor
Figure 22
and
Hardware Design Guidelines
Figure 23
illustrate
59
Related parts for PRIXP425ABC 885156
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801FB I/O Controller Hub (ICH6)
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel Strataflash Memory28F128J3 28F640J3 28F320J3
Manufacturer:
Intel Corporation
Datasheet: