H3CR-F AC/DC24 Omron Automation, H3CR-F AC/DC24 Datasheet
H3CR-F AC/DC24
Specifications of H3CR-F AC/DC24
Related parts for H3CR-F AC/DC24
H3CR-F AC/DC24 Summary of contents
Page 1
... Models with a flicker ON start or flicker OFF start are available. • Easy sequence checks through instantaneous outputs for a zero set value at any time range. • Length, when panel-mounted with a Socket less. • 11-pin and 8-pin models are available. Model Number Structure ■ Model Number Legend H3CR - Classification 3. Twin Timer Mode ...
Page 2
... P3GA-11 with Y92A-48G (See note 1) Y92H-7 Y92H-8 H3CR-F8 H3CR-FN Flicker ON start 8-pin 11-pin ×10 s (10 sec) min (min) 1 0. 120 1 300 ×10 min (10 min) h (hrs) 1 0. 120 1 300 H3CR-F Models H3CR-F8N 8-pin h (hrs) ×10 h (10 hrs) 1 120 30 to 300 2 ...
Page 3
... EN61812-1 EN55011 Group 1 class A EN55011 Group 1 class A EN61812-1 IEC61000-4- contact discharge (level air discharge (level 3) IEC61000-4-3: 10 V/m (80 MHz to 1 GHz) (level (0. MHz) (level 3) IEC61000-4- power-line (level I/O signal-line (level 4) IEC61000-4- line to line (level line to ground (level 3) H3CR-F 3 ...
Page 4
... The minimum applicable load VDC (failure level: P). Zero setting OFF indicator detection circuit Indicator circuit ROM RAM Clock One-chip microcomputer H3CR-F H3CR-FN H3CR-F-300 H3CR-FN-300 Power supply Note: Leave terminals 5, 6, and 7 open. Do not use them as relay terminals. H3CR-F Output circuit Time range/unit selectors (+)(~) 4 ...
Page 5
... ON-time setting knob (with orange pointer) For ON-time setting OFF-time setting knob (with green pointer) For OFF-time setting ON-time unit display window ON-time unit selector (select one from sec min, and hrs, or from min, hrs, and 10 h) H3CR-F 0.1 s min OFF OFF 0.1 s min. t ...
Page 6
... R1.3 17 dia dia. R1.3 Dimensions with Back Connecting Socket P3G-08/P3GA-11 81.5 17.4 80 H3CR-F8 H3CR-F8N 90.0 H3CR-F H3CR-FN P3GA-11 Y92F-30 (When * Y92A-48G 2.3 P2CF-08 mounted) P2CF-08-E H3CR-F 66.6 52.3 0.7 6 44.8 × 44.8 11 pins 66.6 0.7 5.7 52.3 6 44.8 × ...
Page 7
... A time range (1.2, 3, 12, or 30/2. for H3CR-A@-301) is selected with the time range selector at the lower left corner of the front panel, and the selected time range appears (in the window at the lower right part) within the plastic frame of the time setting knob ...
Page 8
... No time unit selector is available. When ordering the H3CR-H, specify S (for the second unit (for the minute unit) for your H3CR-H. Setting of Time Use the time setting knob to set the desired time. ...
Page 9
... Note: All units are in millimeters unless otherwise indicated. Flush Mounting Adaptor Y92F-30 Note: The adapters for two or more timers mounted in a vertical line are different in orientation from those mounted in a horizontal line. N can be obtained as follows (n: the number of H3CR models arranged side by side) +1 Without a Cover (48n - 2. With the Protective Cover (51n - 5 ...
Page 10
... Terminal Arrangement/ Internal Connections 35.4 (Top View) 31.2 max. 7.8 5 4.5 3 1.2 35.4 Two, 4.5 dia. holes 30 31.2 max. H3CR Surface Mounting Holes Two, 4.5 dia. or two, M4 40±0.2 Surface Mounting Holes Two, 4.5 dia. or two, M4 40±0.2 4 ...
Page 11
... Internal Connections (Bottom View) 25.6 4.5 6.2 16.3 Twelve, 6.4 dia. holes 47.7 × 47.7 34 16.5 24.6 27.6 47.4 PFP-100N2 7.3±0.15 4.5 27±0.15 35±0 1,000 Spacer 10 PFP-S 6.2 1.8 1 35.5 35.3 1.8 1.3 4.8 H3CR 48 × 35±0 34.8 44.3 16.5 5 ...
Page 12
... Do not set the selectors midway between notches, otherwise the Timer may break or malfunction. Do not use H3CR-A models (except for H3CR-A@S) in flicker mode, or H3CR-F models at the lowest selector setting. Doing so may result in damage to contacts. Power Supplies A DC power supply can be connected if its ripple factor is 20% or less and the mean voltage is within the rated operating voltage range of the Timer ...
Page 13
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a ...