LM4910MM/NOPB National Semiconductor, LM4910MM/NOPB Datasheet - Page 11

• Manufacturer Part Number: LM4910MM/NOPB
• Description: IC AMP AUDIO PWR .035W AB 8MSOP
• Manufacturer: National Semiconductor
• Series: Boomer®r
• Type: Class ABr

Specifications of LM4910MM/NOPB

• Output Type: Headphones, 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 35mW x 2 @ 32 Ohm
• Voltage - Supply: 2.2 V ~ 5.5 V
• Features: Depop, Shutdown, Thermal Protection
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LM4910MM; LM4910MMTR

POWER SUPPLY BYPASSING
As with any amplifier, proper supply bypassing is important
for low noise performance and high power supply rejection.
The capacitor location on the power supply pins should be as
close to the device as possible.
Typical applications employ a 3.3V regulator with 10µF tan-
talum or electrolytic capacitor and a ceramic bypass capacitor
which aid in supply stability. This does not eliminate the need
for bypassing the supply nodes of the LM4910. A bypass ca-
pacitor value in the range of 0.1µF to 1µF is recommended
for C
MICRO POWER SHUTDOWN
The voltage applied to the SHUTDOWN pin controls the
LM4910's shutdown function. Activate micro-power shutdown
by applying a logic-low voltage to the SHUTDOWN pin. When
active, the LM4910's micro-power shutdown feature turns off
the amplifier's bias circuitry, reducing the supply current. The
trigger point is 0.4V(max) for a logic-low level, and 1.5V(min)
for a logic-high level. The low 0.1µA(typ) shutdown current is
achieved by applying a voltage that is as near as ground as
possible to the SHUTDOWN pin. A voltage that is higher than
ground may increase the shutdown current.
There are a few ways to control the micro-power shutdown.
These include using a single-pole, single-throw switch, a mi-
croprocessor, or a microcontroller. When using a switch,
connect an external 100kΩ pull-up resistor between the
SHUTDOWN pin and V
SHUTDOWN pin and ground. Select normal amplifier opera-
tion by opening the switch. Closing the switch connects the
SHUTDOWN pin to ground, activating micro-power shut-
down. The switch and resistor guarantee that the SHUT-
DOWN pin will not float. This prevents unwanted state
changes. In a system with a microprocessor or microcon-
troller, use a digital output to apply the control voltage to the
SHUTDOWN pin. Driving the SHUTDOWN pin with active
circuitry eliminates the pull-up resistor.
SELECTING EXTERNAL COMPONENTS
Selecting proper external components in applications using
integrated power amplifiers is critical to optimize device and
system performance. While the LM4910 is tolerant of external
component combinations, consideration to component values
must be used to maximize overall system quality.
The LM4910 is unity-gain stable which gives the designer
maximum system flexibility. The LM4910 should be used in
low gain configurations to minimize THD+N values, and max-
imize the signal to noise ratio. Low gain configurations require
large input signals to obtain a given output power. Input sig-
nals equal to or greater than 1V
such as audio codecs. Very large values should not be used
for the gain-setting resistors. Values for R
less than 1MΩ. Please refer to the section, Audio Power
Amplifier Design, for a more complete explanation of proper
gain selection
Besides gain, one of the major considerations is the closed-
loop bandwidth of the amplifier. To a large extent, the band-
width is dictated by the choice of external components shown
in Figure 1. The input coupling capacitor, C
high pass filter which limits low frequency response. This val-
ue should be chosen based on needed frequency response
and turn-on time.
SELECTION OF INPUT CAPACITOR SIZE
Amplifiying the lowest audio frequencies requires a high value
input coupling capacitor, C
S
.
DD
. Connect the switch between the
i
. A high value capacitor can be
rms
are available from sources
i
i
, forms a first order
and R
f
should be
11
expensive and may compromise space efficiency in portable
designs. In many cases, however, the headphones used in
portable systems have little ability to reproduce signals below
60Hz. Applications using headphones with this limited fre-
quency response reap little improvement by using a high
value input capacitor.
In addition to system cost and size, turn-on time is affected
by the size of the input coupling capacitor Ci. A larger input
coupling capacitor requires more charge to reach its quies-
cent DC voltage. This charge comes from the output via the
feedback Thus, by minimizing the capacitor size based on
necessary low frequency response, turn-on time can be min-
imized. A small value of Ci (in the range of 0.1µF to 0.39µF),
is recommended.
USING EXTERNAL POWERED SPEAKERS
The LM4910 is designed specifically for headphone opera-
tion. Often the headphone output of a device will be used to
drive external powered speakers. The LM4910 has a differ-
ential output to eliminate the output coupling capacitors. The
result is a headphone jack sleeve that is connected to V
instead of GND. For powered speakers that are designed to
have single-ended signals at the input, the click and pop cir-
cuitry will not be able to eliminate the turn-on/turn-off click and
pop. Unless the inputs to the powered speakers are fully dif-
ferential the turn-on/turn-off click and pop will be very large.
AUDIO POWER AMPLIFIER DESIGN
A 30mW/32Ω Audio Amplifier
A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the Typical Per-
formance Characteristics section, the supply rail can be
easily found.
Since 3.3V is a standard supply voltage in most applications,
it is chosen for the supply rail in this example. Extra supply
voltage creates headroom that allows the LM4910 to repro-
duce peaks in excess of 30mW without producing audible
distortion. At this time, the designer must make sure that the
power supply choice along with the output impedance does
no violate the conditions explained in the Power Dissipa-
tion section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 2.
From Equation 2, the minimum A
the desired input impedance is 20kΩ, and with A
a ratio of 1:1 results from Equation 1 for R
are chosen with R
The last step in this design example is setting the amplifier's
−3dB frequency bandwidth. To achieve the desired ±0.25dB
pass band magnitude variation limit, the low frequency re-
Given:
Power Output
Load Impedance
Input Level
Input Impedance
i
= 20kΩ and R
V
f
= 20kΩ.
is 0.98; use A
f
to R
i
. The values
V
www.national.com
V
30mWrms
equal to 1,
= 1. Since
1Vrms
20kΩ
32Ω
(2)
O3