saa7803 NXP Semiconductors, saa7803 Datasheet - Page 30
saa7803
Manufacturer Part Number
saa7803
Description
Saa7803 One Chip Cd Audio Device
Manufacturer
NXP Semiconductors
Datasheet
1.SAA7803.pdf
(74 pages)
- Current page: 30 of 74
- Download datasheet (345Kb)
Philips Semiconductors
9397 750 13695
Objective data sheet
6.6.5.4 Run length 2 pushback detector
6.6.5.5 Available signals for monitoring
If this circuit is switched on, all run length 1 (RL1) and run length 2 (RL2) symbols (invalid
run lengths) are pushed back to run length 3 (RL3). For RL2s, the circuit will determine
the transition that was most likely to be in error, and shift transition on that edge. This
feature should always be turned on, but can be deselected via register RL2PushBack.
The operation of the bit detector can be monitored by the microprocessor and using an
external pin. Several signals are made available for measurement.
PLL frequency signal:
Monitoring via the microprocessor is done by reading the register PLLIntegrator.
Asymmetry signal:
signal. The signal is in 2-complement form and can be read from register SlicerAssym.
Jitter signal:
in register PLLJitter.
The jitter measurement is done in two steps.
First, the distance between the EFM zero transition and the bit clock zero transition is
measured.
Table 6:
Second, the calculated jitter for the zero transition is averaged using a 10-bit low-pass
filter. The top 8 bits of the filter output can be read back from register PLLJitter. To obtain
the jitter in % of the channel bit clock, the following formula applies:
This jitter measurement is also available via the telemetry signal on pin MEAS. On this
signal, the full 10-bit output of the filter is available - see
measurement signal on MEAS
It is also possible to read out an average jitter value via register PLLAverageJitter. This
value is an average over a period of 8000 bit clocks on the normal jitter value. The formula
to transform this into % is the same:
average jitter
Distance ( f
<
2
4
>
jitter
16
16
2
6
16
16
to
to
4
6
=
16
16
Jitter input calculation
------------------------------------------ -
jitter 7:0
bit
A jitter measurement is done internally. The zero-crossing jitter is available
)
=
1024
average jitter[7:0] 2.83
----------------------------------------------------------------- -
The second signal that can be monitored is the 8-bit asymmetry
–
2.83
Rev. 01 — 19 April 2005
The first signal that can be monitored is the PLL frequency signal.
100
1024
Average distance (bit clocks) Jitter filter input (5-bit
1
3
5
7
pin”.
16
16
16
16
%
–
100
%
Section 6.6.5.6 “Format of the
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
decimal integer)
1
9
25
49
One chip CD audio device
SAA7803
30 of 74
Related parts for saa7803
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: