saa7803 NXP Semiconductors, saa7803 Datasheet - Page 46
saa7803
Manufacturer Part Number
saa7803
Description
Saa7803 One Chip Cd Audio Device
Manufacturer
NXP Semiconductors
Datasheet
1.SAA7803.pdf
(74 pages)
- Current page: 46 of 74
- Download datasheet (345Kb)
Philips Semiconductors
9397 750 13695
Objective data sheet
6.6.8.5 Writing and reading motor integrator value
6.6.8.6 Some notes on application motor servo
6.7.1 PDSIC Registers and servo RAM control
6.7 Digital Servo - PDSIC
It is possible to obtain the integrator value by reading the registers MotorIntLSB and
MotorIntMSB. The integrator can be written at the same location. By opening all switches,
the user can bypass the whole control and filter part, and just use the block as a DAC for
the motor drivers. The control part can then be done in software.
The motor servo can be used to control the motor during CLV playback and also during
CAV or pseudo-CLV lock-to-disc or jump mode.
The digital servo block on SAA7803 is an evolution of the design used for the SAA7824
IC, and is referred to as Parallel Digital Servo IC (PDSIC). The ‘parallel’ description refers
to the microprocessor interface to the servo block; this is now a high speed parallel
interface, whereas it was previously a serial interface (e.g. SAA7824 3/4 wire, I
The other features of the PDSIC are:
The servo block is controlled by two parts of the design - the servo control registers which
are used to control the writing of commands and parameters to the servo; and the servo
RAM. The servo RAM has two roles: storage of the servo parameters and capture of
commands and parameters during the command process.
All of the servo write commands consist of a command byte followed by a number of
parameter bytes (between 1 and 7), all of which have to be loaded into the PDSIC using a
serial communication interface.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
In CLV mode, both SW1 and SW2 must be closed
In CAV / pseudo-CLV mode, SW2 must be open and SW1 may be open
The motor servo will revolve the disc at the speed corresponding to the frequency set
point; in CLV mode with lock to EFM, the frequency set point must be set equal to the
desired readout frequency of the HF-PLL
Accelerating the disc must be done in one of the start modes
Braking the disc must be done in one of the stop modes.
Programmable ADC for CD-RW playback compatibility
Diode signal processing
Signal conditioning
Focus and radial control system
Access control
Sledge control
Shock detector
Defect detector
Off-track counting and detection
Automatic closed-loop gain control available for focus and radial loops
High level features.
Rev. 01 — 19 April 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
One chip CD audio device
SAA7803
2
C-bus).
46 of 74
Related parts for saa7803
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: