MC3PHACVPE Freescale Semiconductor, MC3PHACVPE Datasheet - Page 29

• Manufacturer Part Number: MC3PHACVPE
• Description: IC MOTOR CONTROLLER 28-DIP
• Manufacturer: Freescale Semiconductor

Specifications of MC3PHACVPE

• Applications: AC Motor Controller, 3 Phase
• Number Of Outputs: 1
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Through Hole
• Package / Case: 28-DIP (0.600", 15.24mm)
• Processor Series: MC3PHAC
• Core: HC08
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 256 KB
• Interface Type: RS-232
• Maximum Clock Frequency: 21.16 KHz
• Number Of Programmable I/os: 14
• Number Of Timers: 1
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Controller Family/series: HC08
• Core Size: 8 Bit
• Ram Memory Size: 256Byte
• Embedded Interface Type: SCI
• Digital Ic Case Style: DIP
• No. Of Pins: 28
• A/d Converter: 10 Bits
• No. Of Timers 8/12/16/32 Bits: 0/0/2/0
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Voltage - Load: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor
Fault
SetBaseFreq
SetBaseFreq
SetSpeed
SetSpeed
FwdDecel
SetAccel
SetAccel
CmdBaseFreqxx
CmdBaseFreqxx
from any state
from any state
WRITEVAR16:Acceleration
WRITEVAR16:Acceleration
from any state
from any state
WRITEVAR16:Speed
WRITEVAR16:Speed
In from any state
In from any state
Done
Done
(return to
(return to
calling
calling
state)
state)
Done
Done
(return to
(return to
calling
calling
state)
state)
Done
Done
(return to
(return to
calling
calling
state)
state)
Fault
Figure 18. PC Host Software Command State Diagram
CmdRev &
Actual speed = 0
CmdRev |
CmdStop
Actual speed =
Speed In
MC3PHAC Monolithic Intelligent Motor Controller, Rev. 2
FwdSteady
FwdAccel
Done & CmdFwd
CmdReset
Speed In >
Actual Speed
PWMHighZ
PWM0RPM
PWMOFF
PWMPump
Reset
Initialized
CmdFwd |
PWM dead-time set &
PWM polarity set
CmdRev
Speed In >
Actual Speed
PWM base freq. set &
Acceleration set &
Speed In set
Done & CmdRev
RevAccel
RevSteady
Reset or
POR or
Loss of Crystal or
Internal Error
CmdPWMTxBx
done
CmdFwd &
Actual speed = 0
Actual speed =
Speed In
CmdFwd |
CmdStop
Execute PC
Execute PC
Master Cmd
Master Cmd
SetDeadTime
Other PC Master
Other PC Master
command from any state
command from any state
Done
Done
(return to
(return to
calling
calling
state)
state)
SetPolarity
PC master software
command from any state
(write once)
(write once)
RevDecel
Operation
29