ADC08100EVAL National Semiconductor, ADC08100EVAL Datasheet
ADC08100EVAL
Specifications of ADC08100EVAL
Related parts for ADC08100EVAL
ADC08100EVAL Summary of contents
Page 1
... National Semiconductor Evaluation Board Instruction Manual ADC08100 8-Bit, 20 Msps to 130Msps, Analog-to-Digital Converter with Internal Sample & Hold © 2002 National Semiconductor Corporation. 1 August 2002 Rev 2 http://www.national.com ...
Page 2
Blank Page ] 2 http://www.national.com ...
Page 3
Introduction ............................................................................................................................5 2.0 Board Assembly ....................................................................................................................5 3.0 Quick Start.............................................................................................................................5 4.0 Functional Description ...........................................................................................................6 4.1 Input (signal conditioning) circuitry ............................................................................6 4.2 ADC reference circuitry ............................................................................................6 4.3 ADC clock circuit ......................................................................................................6 4.4 Digital Data Output. ..................................................................................................7 4.5 Power Supply Connections.......................................................................................7 4.6 ...
Page 4
Blank Page ] 4 http://www.national.com ...
Page 5
... Introduction The ADC08100EVAL Design Kit (consisting of the ADC08100 Evaluation Board, National's WaveVision software and this manual) is designed to ease evaluation and design-in of Nationals ADC08100 8-bit Analog-to- Digital Converter, which operate at sample rates up to 130 Msps. The WaveVision software operates under Microsoft Windows ...
Page 6
... J5 Detail: Default is open J1 Detail: Hard-wired Default Position NATIONAL SEMICONDUCTOR ADC08100/ADC08200 EVAL BOARD J4 Detail: Default Position Figure 1. Component and Test Point Locations 4.0 Functional Description The ADC08100 Evaluation Board schematic is shown in Figure 2. 4.1 Input (signal conditioning) circuitry The input signal to be digitized should be applied to BNC connector J2 ...
Page 7
Caution: Be sure that the oscillator used has logic levels of -0.6V and -1.3V. We have found oscillators with levels that are too low to work properly in the circuit designed for this board. R4 and C1 are used for ...
Page 8
Perform steps 1 through 7 of Section 5.2.1.1. Adjust the input signal at J2 for 1.6V P JP4 - Short the two pins farthest from Y1 (pins 1 & divide the on-board clock oscillator by ...
Page 9
Troubleshooting "Comm Check Failed", "Error Transmitting", "Parallel Port Time Out Error" and/or "Failed to communicate with the board on LPT1" errors mean communication was unsuccessful. Try the following: Be sure to wait for yellow LED D4 on the Digital ...
Page 10
Hardware Schematic D8 D7 RD7 30 D6 RD6 31 D5 RD5 1 D4 RD4 2 D3 RD3 3 D2 RD2 RD7 30 D6 RD6 31 D5 RD5 1 D4 RD4 2 D3 RD3 3 D2 RD2 ...
Page 11
http://www.national.com ...
Page 12
... Breakable Header DigiKey # S1012-36-ND Signal Transformer MiniCircuits type T4-6T ADC08100 National Semiconductor CY7C4281 Cypress Semiconductor LM833N National Semiconductor 74F74 Various LM2931CT National Semiconductor MC10H125FN ON Semiconductor MC10H131FN ON Semiconductor 1k DigiKey # 3386F-103-ND 100MHz Low Jitter, ECL Output For U2 DigiKey # A2121-ND For U4 DigiKey # A400-ND For T1 ...
Page 13
Summary Tables of Test Points and Connectors Test Points on the ADC08100 Evaluation Board TP 1 Power Down Input. Pull high to power down the ADC08100 TP 2 ADC Top Reference Voltage TP 3 Ground TP 4 ADC Bottom Reference ...
Page 14
J3 Connector - ADC Data Outputs - Connection to WaveVision Digital Interface Board Signal J2 pin number ADC output D0 B16 ADC output D1 C16 ADC output D2 B17 ADC output D3 C17 ADC output D4 B18 ADC output D5 ...
Page 15
Blank Page ] 15 http://www.national.com ...
Page 16
... The ADC08100 Evaluation Board is intended for product evaluation purposes only and is not intended for resale to end consumers, is not authorized for such use and is not designed for compliance with European EMC Directive 89/336/EEC. WaveVision is a trademark of National Semiconductor Corporation. National does not assume any responsibility for use of any circuitry or software supplied or described. No circuit patent licenses are implied. ...