PIC18F27J53-I/SP Microchip Technology, PIC18F27J53-I/SP Datasheet - Page 12

• Manufacturer Part Number: PIC18F27J53-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: *
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Embedded Interface Type: I2C, SPI, USART
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2XJXX/4XJXX FAMILY
3.2
Programming code memory is accomplished by first
loading data into the write buffer and then initiating a
programming sequence. The write buffer for all devices
in the PIC18F2XJXX/4XJXX family is 64 bytes. It can
be mapped to any 64-byte block beginning at 000000h.
The actual memory write sequence takes the contents
of this buffer and programs the 64-byte block of code
memory indicated by the Table Pointer.
Write buffer locations are not cleared following a write
operation; the buffer retains its data after the write is
complete. This means that the buffer must be written
with 64 bytes on each operation. If there are locations
in the code memory that are to remain empty, the
corresponding locations in the buffer must be filled with
FFFFh. This avoids rewriting old data from the previous
cycle.
TABLE 3-3:
DS39687E-page 12
Step 1: Enable writes.
Step 2: Load write buffer.
Step 3: Repeat for all but the last two bytes. Any unused locations should be filled with FFFFh.
Step 4: Load write buffer for last two bytes.
To continue writing data, repeat steps 2 through 4, where the Address Pointer is incremented by 2 at each iteration of the loop.
Command
0000
0000
0000
0000
0000
0000
0000
1101
1111
0000
4-Bit
Code Memory Programming
84 A6
0E <Addr[21:16]>
6E F8
0E <Addr[15:8]>
6E F7
0E <Addr[7:0]>
6E F6
<MSB><LSB>
<MSB><LSB>
00 00
WRITE CODE MEMORY CODE SEQUENCE
Data Payload
BSF
MOVLW <Addr[21:16]>
MOVWF TBLPTRU
MOVLW <Addr[15:8]>
MOVWF TBLPTRH
MOVLW <Addr[7:0]>
MOVWF TBLPTRL
Write 2 bytes and post-increment address by 2.
Write 2 bytes and start programming.
NOP - hold PGC high for time P9.
EECON1, WREN
The programming duration is internally timed. After a
Start Programming command is issued (4-bit com-
mand, ‘1111’), a NOP is issued, where the 4th PGC is
held high for the duration of the programming time, P9.
The
PIC18F2XJXX/4XJXX family device is shown in
Table 3-3. The flowchart shown in Figure 3-5 depicts
the
PIC18F2XJXX/4XJXX family device. The timing
diagram that details the Start Programming command
and parameter P9 is shown in Figure 3-6.
Note 1: The TBLPTR register must point to the
logic
Core Instruction
code
same region when initiating the program-
ming sequence as it did when the write
buffers were loaded.
necessary
sequence
© 2009 Microchip Technology Inc.
to
completely
to
program
write
a
a