PIC18F27J53-I/SP Microchip Technology, PIC18F27J53-I/SP Datasheet - Page 24

• Manufacturer Part Number: PIC18F27J53-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: *
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Embedded Interface Type: I2C, SPI, USART
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2XJXX/4XJXX FAMILY
TABLE 5-7:
DS39687E-page 24
DEBUG
XINST
STVREN
CFGPLLEN
PLLDIV<2:0>
WDTEN
CP0
CPDIV<1:0>
IESO
FCMEN
CLKOEC
SOSCSEL<1:0>
Note 1: The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
(4)
Bit Name
2: The Configuration bits are reset to ‘1’ only on V
3: These bits are not implemented in PIC18F47J13 family devices.
4: Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
5: Not implemented on PIC18F47J53 family devices.
(3)
protection, perform an ICSP™ Bulk Erase operation.
PIC18F47J13 AND PIC18F47J53 FAMILY DEVICES: BIT DESCRIPTIONS
CONFIG2L
CONFIG2L
Configuration
CONFIG1H
CONFIG1H
CONFIG1L
CONFIG1L
CONFIG1L
CONFIG1L
CONFIG1L
CONFIG1L
CONFIG2L
CONFIG2L
Words
(1,2)
(1,2)
Background Debugger Enable bit
1 = Background debugger disabled, RB6 and RB7 configured as general purpose
0 = Background debugger enabled, RB6 and RB7 are dedicated to in-circuit debug
Enhanced Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
Stack Overflow/Underflow Reset Enable bit
1 = Reset on stack overflow/underflow enabled
0 = Reset on stack overflow/underflow disabled
Enable PLL on Start-up bit
1 = PLL enabled on start-up. Not recommended for low-voltage designs.
0 = PLL disabled on start-up. Firmware may later enable PLL through OSCTUNE<6>.
96 MHz PLL Input Divider bits
Divider must be selected to provide a 4 MHz input into the 96 MHz PLL.
111 = No divide – oscillator used directly (4 MHz input)
110 = Oscillator divided by 2 (8 MHz input)
101 = Oscillator divided by 3 (12 MHz input)
100 = Oscillator divided by 4 (16 MHz input)
011 = Oscillator divided by 5 (20 MHz input)
010 = Oscillator divided by 6 (24 MHz input)
001 = Oscillator divided by 10 (40 MHz input)
000 = Oscillator divided by 12 (48 MHz input)
Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled (control is placed on SWDTEN bit)
Code Protection bit
1 = Program memory is not code-protected
0 = Program memory is code-protected
CPU System Clock Selection bits
11 = No CPU system clock divide
10 = CPU system clock divided by 2
01 = CPU system clock divided by 3
00 = CPU system clock divided by 6
Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit
1 = Oscillator Switchover mode enabled
0 = Oscillator Switchover mode disabled
Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
EC Mode Clock Output Enable bit
1 = CLKO output signal active on the RA6 pin (EC mode only)
0 = CLKO output disabled
Secondary Oscillator Circuit Selection bits
11 = High-power SOSC circuit selected
10 = Digital Input mode (SCLKI)
01 = Low-power SOSC circuit selected
00 = Reserved
I/O pins
DD
Reset; it is reloaded with the programmed value at any device Reset.
Description
© 2009 Microchip Technology Inc.