T89C51CC02CA-TDSIM Atmel, T89C51CC02CA-TDSIM Datasheet - Page 36

• Manufacturer Part Number: T89C51CC02CA-TDSIM
• Description: IC 8051 MCU FLASH 16K 24SOIC
• Manufacturer: Atmel
• Series: AT89C CANr

Specifications of T89C51CC02CA-TDSIM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-SOIC (7.5mm Width)
• For Use With: AT89STK-06 - KIT DEMOBOARD 8051 MCU W/CAN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: T89C51CC02CATDSIM

Overview of FM0
Operations
Mapping of the Memory Space By default, the user space is accessed by MOVC instruction for read only. The column
Launching Programming
36
AT/T89C51CC02
The CPU interfaces the Flash memory through the FCON register and AUXR1 register.
These registers are used to:
•
•
•
latches space is made accessible by setting the FPS bit in FCON register. Writing is
possible from 0000h to 3FFFh, address bits 6 to 0 are used to select an address within a
page while bits 14 to 7 are used to select the programming address of the page.
Setting FPS bit takes precedence on the EEE bit in EECON register.
The other memory spaces (user, extra row, hardware security) are made accessible in
the code segment by programming bits FMOD0 and FMOD1 in FCON register in accor-
dance with Table 22. A MOVC instruction is then used for reading these spaces.
Table 22. FM0 blocks Select bits
FPL3:0 bits in FCON register are used to secure the launch of programming. A specific
sequence must be written in these bits to unlock the write protection and to launch the
programming. This sequence is 5xh followed by Axh. Table 23 summarizes the memory
spaces to program according to FMOD1:0 bits.
Table 23. Programming Spaces
Note:
Extra Row
Hardware
Reserved
Security
User
Byte
Map the memory spaces in the adressable space
Launch the programming of the memory spaces
Get the status of the Flash memory (busy/not busy)
FMOD1
The sequence 5xh and Axh must be executing without instructions between them other-
wise the programming is aborted.
Interrupts that may occur during programming time must be disabled to avoid any spuri-
ous exit of the programming mode.
0
0
1
1
FPL3:0
A
A
A
A
5
5
5
5
FMOD0
FPS
0
1
0
1
Write to FCON
x
x
x
x
x
x
x
x
FMOD1
FM0 Adressable Space
User (0000h-3FFFh)
Extra Row(FF80h-FFFFh)
Hardware Security Byte (0000h)
Reserved
0
0
0
0
1
1
1
1
FMOD0
0
0
1
1
0
0
1
1
Operation
No action
Write the column latches in user
space
No action
Write the column latches in extra row
space
No action
Write the fuse bits space
No action
No action
4126L–CAN–01/08