PIC24FJ256GA106-I/PT Microchip Technology, PIC24FJ256GA106-I/PT Datasheet - Page 40
![IC PIC MCU FLASH 256K 64TQFP](/photos/6/81/68123/c04-066_pf_sml.jpg)
PIC24FJ256GA106-I/PT
Manufacturer Part Number
PIC24FJ256GA106-I/PT
Description
IC PIC MCU FLASH 256K 64TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Fr
Datasheets
1.PIC24FJ128GA008-IPT.pdf
(12 pages)
2.PIC24FJ128GA106-IPT.pdf
(14 pages)
3.PIC24FJ128GA106-IPT.pdf
(330 pages)
4.PIC24FJ128GA106-IPT.pdf
(52 pages)
5.PIC24FJ256GA106-IPT.pdf
(59 pages)
6.PIC24FJ128GB110-IPF.pdf
(292 pages)
Specifications of PIC24FJ256GA106-I/PT
Program Memory Type
FLASH
Program Memory Size
256KB (85.5K x 24)
Package / Case
64-TFQFP
Core Processor
PIC
Core Size
16-Bit
Speed
32MHz
Connectivity
I²C, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
53
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
16 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
53
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
Minimum Operating Temperature
- 40 C
On-chip Adc
16-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARDMA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC164327 - MODULE SKT FOR 64TQFP
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24FJ256GA106-I/PT
Manufacturer:
AD
Quantity:
201
Company:
Part Number:
PIC24FJ256GA106-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC24FJXXXDA1/DA2/GB2/GA3
4.6.2
Configuration bits may be programmed a single word at
a time using the PROGW command. This command
specifies the configuration data and Configuration
register
programmed, any unimplemented or reserved bits
must be programmed with a ‘1’.
Four PROGW commands are required to program the
Configuration bits. See
Configuration bit programming.
FIGURE 4-5:
DS39970B-page 40
Note:
Note 1: Refer to
address.
PROGRAMMING METHODOLOGY
If the General Segment Code-Protect bit
(GCP) is programmed to ‘0’, code memory
is code-protected and cannot be read. Code
memory must be verified before enabling
read
“Code-Protect Configuration Bits”
more information about code-protect
Configuration bits.
protection.
When
ConfigAddress + 2
ConfigAddress =
CONFIGURATION BIT PROGRAMMING FLOW
Table 2-2
Figure 4-5
Configuration
for Flash Configuration Word addresses.
See
for a flowchart for
Section 4.6.4
bits
No
for
are
PROGP response
Send PROGW
ConfigAddress
0XXXFEh?
Command
PASS?
Start
4.6.3
After the Configuration bits are programmed, the
contents of memory should be verified to ensure that
the programming was successful. Verification requires
the Configuration bits to be read back and compared
with the copy held in the programmer’s buffer. The
READP command reads back the programmed
Configuration bits and verifies that the programming
was successful.
End
Is
Is
Yes
Yes
(1)
ConfigAddress = 0XXXF8h
PROGRAMMING VERIFICATION
No
Report Error
2010 Microchip Technology Inc.
Failure
(1)