PIC24FJ256GA106-I/PT Microchip Technology, PIC24FJ256GA106-I/PT Datasheet - Page 212
![IC PIC MCU FLASH 256K 64TQFP](/photos/6/81/68123/c04-066_pf_sml.jpg)
PIC24FJ256GA106-I/PT
Manufacturer Part Number
PIC24FJ256GA106-I/PT
Description
IC PIC MCU FLASH 256K 64TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Fr
Datasheets
1.PIC24FJ128GA008-IPT.pdf
(12 pages)
2.PIC24FJ128GA106-IPT.pdf
(14 pages)
3.PIC24FJ128GA106-IPT.pdf
(330 pages)
4.PIC24FJ128GA106-IPT.pdf
(52 pages)
5.PIC24FJ256GA106-IPT.pdf
(59 pages)
6.PIC24FJ128GB110-IPF.pdf
(292 pages)
Specifications of PIC24FJ256GA106-I/PT
Program Memory Type
FLASH
Program Memory Size
256KB (85.5K x 24)
Package / Case
64-TFQFP
Core Processor
PIC
Core Size
16-Bit
Speed
32MHz
Connectivity
I²C, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
53
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
16 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
53
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
Minimum Operating Temperature
- 40 C
On-chip Adc
16-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARDMA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC164327 - MODULE SKT FOR 64TQFP
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24FJ256GA106-I/PT
Manufacturer:
AD
Quantity:
201
Company:
Part Number:
PIC24FJ256GA106-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC24FJ256GA110 FAMILY
FIGURE 19-2:
19.1
19.1.1
To start serial shifting, a ‘1’ must be written to the
CRCGO bit.
The module incorporates a FIFO that is 8 deep when
PLEN (CRCCON<3:0>) > 7, and 16 deep, otherwise.
The data for which the CRC is to be calculated must
first be written into the FIFO. The smallest data element
that can be written into the FIFO is one byte. For
example, if PLEN = 5, then the size of the data is
PLEN + 1 = 6. The data must be written as follows:
Once data is written into the CRCWDAT MSb (as
defined
(CRCCON<12:8>) increments by one. The serial
shifter starts shifting data into the CRC engine when
CRCGO = 1 and VWORD > 0. When the MSb is
shifted out, VWORD decrements by one. The serial
shifter continues shifting until the VWORD reaches 0.
Therefore, for a given value of PLEN, it will take
(PLEN + 1) * VWORD number of clock cycles to
complete the CRC calculations.
When VWORD reaches 8 (or 16), the CRCFUL bit will
be set. When VWORD reaches 0, the CRCMPT bit will
be set.
To continually feed data into the CRC engine, the rec-
ommended mode of operation is to initially “prime” the
FIFO with a sufficient number of words so no interrupt
is generated before the next word can be written. Once
that is done, start the CRC by setting the CRCGO bit to
‘1’. From that point onward, the VWORD bits should be
polled. If they read less than 8 or 16, another word can
be written into the FIFO.
DS39905B-page 210
SDOx
XOR
User Interface
by
DATA INTERFACE
D
data[5:0] = crc_input[5:0]
BIT 0
p_clk
PLEN),
Q
data[7:6] = ‘bxx
CRC GENERATOR RECONFIGURED FOR x
the
D
p_clk
BIT 4
value
Q
of
VWORD
Preliminary
D
BIT 5
p_clk
Q
To empty words already written into a FIFO, the
CRCGO bit must be set to ‘1’ and the CRC shifter
allowed to run until the CRCMPT bit is set.
Also, to get the correct CRC reading, it will be
necessary to wait for the CRCMPT bit to go high before
reading the CRCWDAT register.
If a word is written when the CRCFUL bit is set, the
VWORD Pointer will roll over to 0. The hardware will
then behave as if the FIFO is empty. However, the con-
dition to generate an interrupt will not be met; therefore,
no interrupt will be generated (See Section 19.1.2
“Interrupt Operation”).
At least one instruction cycle must pass after a write to
CRCWDAT before a read of the VWORD bits is done.
19.1.2
When the VWORD4:VWORD0 bits make a transition
from a value of ‘1’ to ‘0’, an interrupt will be generated.
19.2
19.2.1
If Sleep mode is entered while the module is operating,
the module will be suspended in its current state until
clock execution resumes.
19.2.2
To continue full module operation in Idle mode, the
CSIDL bit must be cleared prior to entry into the mode.
If CSIDL = 1, the module will behave the same way as
it does in Sleep mode; pending interrupt events will be
passed on, even though the module clocks are not
available.
Operation in Power Save Modes
16
INTERRUPT OPERATION
SLEEP MODE
IDLE MODE
+ x
12
CRC Read Bus
D
BIT 12
p_clk
+ x
Q
5
© 2008 Microchip Technology Inc.
+ 1
CRC Write Bus
BIT 15
D
p_clk
Q