MC908JB16DWE Freescale Semiconductor, MC908JB16DWE Datasheet - Page 64

• Manufacturer Part Number: MC908JB16DWE
• Description: IC MCU 16K FLASH 6MHZ USB 28SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JB16DWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SCI, USB
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: HC08JB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: I2C/SCI/SPI/USB
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE, KITUSBSPIDGLEVME, KITUSBSPIEVME, KIT33810EKEVME
• Minimum Operating Temperature: 0 C
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FLASH Memory
4.7 FLASH Program Operation
Technical Data
64
NOTE:
Programming of the FLASH memory is done on a row basis. A row
consists of 64 consecutive bytes starting from addresses $XX00,
$XX40, $XX80 or $XXC0. The procedure for programming a row of the
FLASH memory is outlined below:
This program sequence is repeated throughout the memory until all data
is programmed.
Programming and erasing of FLASH locations cannot be performed by
executing code from the FLASH memory; the code must be executed
from RAM. While these operations must be performed in the order as
shown, but other unrelated operations may occur between the steps. Do
not exceed t
Characteristics.
Figure 4-3
FLASH memory.
10. Wait for time, t
11. Clear the HVEN bit.
12. After time, t
1. Set the PGM bit. This configures the memory for program
2. Write any data to any FLASH address within the address range of
3. Wait for a time, t
4. Set the HVEN bit.
5. Wait for a time, t
6. Write data to the byte being programmed.
7. Wait for time, t
8. Repeat steps 6 and 7 until all the bytes within the row are
9. Clear the PGM bit.
operation and enables the latching of address and data for
programming.
the row to be programmed.
programmed.
again.
shows a flowchart representation for programming the
Prog
maximum. See
FLASH Memory
rcv
Prog
nvh
(1µs), the memory can be accessed in read mode
nvs
pgs
(5µs).
(30µs).
(5µs).
(10µs).
20.14 FLASH Memory
MC68HC908JB16
Freescale Semiconductor
—
Rev. 1.1