MC9S12E128CPVE Freescale Semiconductor, MC9S12E128CPVE Datasheet - Page 437

• Manufacturer Part Number: MC9S12E128CPVE
• Description: IC MCU 128K FLASH 25MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12E128CPVE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 2.75 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12E
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 92
• Number Of Timers: 12
• Operating Supply Voltage: 3.135 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• On-chip Dac: 2-ch x 8-bit
• Controller Family/series: HCS12/S12X
• No. Of I/o's: 90
• Ram Memory Size: 8KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: M68EVB912E128 - BOARD EVAL FOR MC9S12E128/64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

The minimum pulse width for the PAI input is greater than two bus clocks.
13.4.5
Clearing the PAMOD bit configures the PACNT for event counter operation. An active edge on the IOC7
pin increments the pulse accumulator counter. The PEDGE bit selects falling edges or rising edges to
increment the count.
The Pulse Accumulator counter register reflect the number of active input edges on the PACNT input pin
since the last reset.
The PAOVF bit is set when the accumulator rolls over from 0xFFFF to 0x0000. The pulse accumulator
overflow interrupt enable bit, PAOVI, enables the PAOVF flag to generate interrupt requests.
13.4.6
Setting the PAMOD bit configures the pulse accumulator for gated time accumulation operation. An active
level on the PACNT input pin enables a divided-by-64 clock to drive the pulse accumulator. The PEDGE
bit selects low levels or high levels to enable the divided-by-64 clock.
The trailing edge of the active level at the IOC7 pin sets the PAIF. The PAI bit enables the PAIF flag to
generate interrupt requests.
The pulse accumulator counter register reflect the number of pulses from the divided-by-64 clock since the
last reset.
13.5
The reset state of each individual bit is listed within
which details the registers and their bit fields.
Freescale Semiconductor
Resets
Event Counter Mode
Gated Time Accumulation Mode
The PACNT input and timer channel 7 use the same pin IOC7. To use the
IOC7, disconnect it from the output logic by clearing the channel 7 output
mode and output level bits, OM7 and OL7. Also clear the channel 7 output
compare 7 mask bit, OC7M7.
The pulse accumulator counter can operate in event counter mode even
when the timer enable bit, TEN, is clear.
The timer prescaler generates the divided-by-64 clock. If the timer is not
active, there is no divided-by-64 clock.
MC9S12E128 Data Sheet, Rev. 1.07
NOTE
NOTE
NOTE
Section 13.3, “Memory Map and Register Definition”
Chapter 13 Timer Module (TIM16B4CV1)
437