MC9S12XDT256CAA Freescale Semiconductor, MC9S12XDT256CAA Datasheet - Page 215

• Manufacturer Part Number: MC9S12XDT256CAA
• Description: IC MCU 256K FLASH 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XDT256CAA

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 59
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Processor Series: S12XD
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 59
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12XDP512E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.8.3
Table 6-16
implies additional wait cycles if memories or peripherals are not accessible. Memories or peripherals are
not accessible if they are blocked by the S12X_CPU. In addition to this Peripherals are only accessible
every other XGATE cycle. Uppercase letters denote 16 bit operations. Lowercase letters denote 8 bit
operations. The XGATE is able to perform two bus or wait cycles per S12X_CPU cycle.
6.8.4
When the RISC core is triggered by an interrupt request (see
sequence which performs three bus accesses:
Afterwards a sequence of instructions (thread) is executed which is terminated by an "RTS" instruction. If
further interrupt requests are pending after a thread has been terminated, a new vector fetch will be
performed. Otherwise the RISC core will idle until a new interrupt request is received. A thread can not be
interrupted by an interrupt request.
6.8.5
This section describes the XGATE instruction set in alphabetical order.
Freescale Semiconductor
1. A V-cycle to fetch the initial content of the program counter.
2. A V-cycle to fetch the initial content of the data segment pointer (R1).
3. A P-cycle to load the initial opcode.
V — Vector fetch: always an aligned word read, lasts for at least one RISC core cycle
P — Program word fetch: always an aligned word read, lasts for at least one RISC core cycle
r — 8 bit data read: lasts for at least one RISC core cycle
R — 16 bit data read: lasts for at least one RISC core cycle
w — 8 bit data write: lasts for at least one RISC core cycle
W — 16 bit data write: lasts for at least one RISC core cycle
A — Alignment cycle: no read or write, lasts for zero or one RISC core cycles
f — Free cycle: no read or write, lasts for one RISC core cycles
Special Cases
PP/P — Branch: PP if branch taken, P if not
show the XGATE access detail notation. Each code letter equals one XGATE cycle. Each letter
Cycle Notation
Thread Execution
Instruction Glossary
Table 6-16. Access Detail Notation
MC9S12XDP512 Data Sheet, Rev. 2.21
Figure
6-1) it first executes a vector fetch
Chapter 6 XGATE (S12XGATEV2)
215