MC56F8345VFGE Freescale Semiconductor, MC56F8345VFGE Datasheet - Page 25

• Manufacturer Part Number: MC56F8345VFGE
• Description: IC DSP 16BIT 60MHZ 128-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8345VFGE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 60MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 49
• Program Memory Size: 136KB (68K x 16)
• Program Memory Type: FLASH
• Ram Size: 6K x 16
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 128-LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F83xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 60 MIPs
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 49
• Data Ram Size: 8 KB
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Interface Type: SCI, SPI, CAN
• Minimum Operating Temperature: - 40 C
• For Use With: MC56F8367EVME - EVAL BOARD FOR MC56F83X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor
Preliminary
(GPIOD7)
Signal
Name
RXD1
TCK
TMS
TDO
TDI
Table 2-2 Signal and Package Information for the 128-Pin LQFP
Pin No.
115
116
117
118
41
Schmitt
Schmitt
Schmitt
Output
Output
Input/
Type
Input
Input
Input
Input
pulled high
pulled high
pulled low
56F8345 Technical Data, Rev. 17
internally
internally
internally
disabled,
pull-up is
output is
enabled
In reset,
enabled
During
pull-up
Reset
Input,
Input,
Input,
Input,
State
Receive Data — SCI1 receive data input
Port D GPIO — This GPIO pin can be individually programmed
as an input or output pin.
After reset, the default state is SCI input.
To deactivate the internal pull-up resistor, clear bit 7 in the
GPIOD_PUR register.
Test Clock Input — This input pin provides a gated clock to
synchronize the test logic and shift serial data to the
JTAG/EOnCE port. The pin is connected internally to a
pull-down resistor.
Test Mode Select Input — This input pin is used to sequence
the JTAG TAP controller’s state machine. It is sampled on the
rising edge of TCK and has an on-chip pull-up resistor.
To deactivate the internal pull-up resistor, set the JTAG bit in the
SIM_PUDR register.
Note:
Test Data Input — This input pin provides a serial input data
stream to the JTAG/EOnCE port. It is sampled on the rising edge
of TCK and has an on-chip pull-up resistor.
To deactivate the internal pull-up resistor, set the JTAG bit in the
SIM_PUDR register.
Test Data Output — This tri-stateable output pin provides a
serial output data stream from the JTAG/EOnCE port. It is driven
in the shift-IR and shift-DR controller states, and changes on the
falling edge of TCK.
Always tie the TMS pin to V
Signal Description
DD
through a 2.2K resistor.
Signal Pins
25