MC9S12XEP100CAL Freescale Semiconductor, MC9S12XEP100CAL Datasheet - Page 1062

• Manufacturer Part Number: MC9S12XEP100CAL
• Description: IC MCU 16BIT 1M FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XEP100CAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 50MHz
• Connectivity: CAN, EBI/EMI, I²C, IrDA, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: S12XE
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 64 KB
• Interface Type: CAN/SCI/SPI
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 25
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: KIT33812ECUEVME, EVB9S12XEP100, DEMO9S12XEP100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 12-bit
• Package: 112LQFP
• Family Name: HCS12X
• Maximum Speed: 50 MHz
• Operating Supply Voltage: 1.8|2.8|5 V
• For Use With: EVB9S12XEP100 - BOARD EVAL FOR MC9S12XEP100DEMO9S12XEP100 - BOARD DEMO FOR MC9S12XEP100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 27 512 KByte Flash Module (S12XFTM512K3V1)
27.4.2.11 Unsecure Flash Command
The Unsecure Flash command will erase the entire P-Flash and D-Flash memory space and, if the erase is
successful, will release security.
Upon clearing CCIF to launch the Unsecure Flash command, the Memory Controller will erase the entire
P-Flash and D-Flash memory space and verify that it is erased. If the Memory Controller verifies that the
entire Flash memory space was properly erased, security will be released. If the erase verify is not
successful, the Unsecure Flash operation sets MGSTAT1 and terminates without changing the security
state. During the execution of this command (CCIF=0) the user must not write to any Flash module
register. The CCIF flag is set after the Unsecure Flash operation has completed.
27.4.2.12 Verify Backdoor Access Key Command
The Verify Backdoor Access Key command will only execute if it is enabled by the KEYEN bits in the
FSEC register (see
supplied keys match those stored in the Flash security bytes of the Flash configuration field (see
3). The Verify Backdoor Access Key command must not be executed from the Flash block containing the
backdoor comparison key to avoid code runaway.
1062
FERSTAT
Register
FSTAT
Table 27-55. Verify Backdoor Access Key Command FCCOB Requirements
Table
CCOBIX[2:0]
CCOBIX[2:0]
Table 27-53. Unsecure Flash Command FCCOB Requirements
MGSTAT1
MGSTAT0
EPVIOLIF
ACCERR
Error Bit
FPVIOL
000
000
001
010
011
100
Table 27-54. Unsecure Flash Command Error Handling
27-11). The Verify Backdoor Access Key command releases security if user-
MC9S12XE-Family Reference Manual , Rev. 1.23
Set if CCOBIX[2:0] != 000 at command launch
Set if a Load Data Field command sequence is currently active
Set if command not available in current mode (see
Set if any area of the P-Flash memory is protected
Set if any errors have been encountered during the verify operation
Set if any non-correctable errors have been encountered during the verify
operation
Set if any area of the buffer RAM EEE partition is protected
0x0C
0x0B
FCCOB Parameters
FCCOB Parameters
Key 0
Key 1
Key 2
Key 3
Error Condition
Not required
Not required
Table
27-30)
Freescale Semiconductor
Table 27-