MC9S12XEP100CAL Freescale Semiconductor, MC9S12XEP100CAL Datasheet - Page 952

IC MCU 16BIT 1M FLASH 112-LQFP

MC9S12XEP100CAL

Manufacturer Part Number
MC9S12XEP100CAL
Description
IC MCU 16BIT 1M FLASH 112-LQFP
Manufacturer
Freescale Semiconductor
Series
HCS12r
Datasheet

Specifications of MC9S12XEP100CAL

Core Processor
HCS12X
Core Size
16-Bit
Speed
50MHz
Connectivity
CAN, EBI/EMI, I²C, IrDA, SCI, SPI
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
91
Program Memory Size
1MB (1M x 8)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
64K x 8
Voltage - Supply (vcc/vdd)
1.72 V ~ 5.5 V
Data Converters
A/D 16x12b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
112-LQFP
Processor Series
S12XE
Core
HCS12
Data Bus Width
16 bit
Data Ram Size
64 KB
Interface Type
CAN/SCI/SPI
Maximum Clock Frequency
50 MHz
Number Of Programmable I/os
91
Number Of Timers
25
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWHCS12
Development Tools By Supplier
KIT33812ECUEVME, EVB9S12XEP100, DEMO9S12XEP100
Minimum Operating Temperature
- 40 C
On-chip Adc
16-ch x 12-bit
Package
112LQFP
Family Name
HCS12X
Maximum Speed
50 MHz
Operating Supply Voltage
1.8|2.8|5 V
For Use With
EVB9S12XEP100 - BOARD EVAL FOR MC9S12XEP100DEMO9S12XEP100 - BOARD DEMO FOR MC9S12XEP100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC9S12XEP100CAL
Manufacturer:
TOSHIBA
Quantity:
72
Part Number:
MC9S12XEP100CAL
Manufacturer:
FREESCALE
Quantity:
2 689
Part Number:
MC9S12XEP100CAL
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC9S12XEP100CAL
Manufacturer:
FREESCALE
Quantity:
2 689
Chapter 25 256 KByte Flash Module (S12XFTM256K2V1)
The security state out of reset can be permanently changed by programming the security byte of the Flash
configuration field. This assumes that you are starting from a mode where the necessary P-Flash erase and
program commands are available and that the upper region of the P-Flash is unprotected. If the Flash
security byte is successfully programmed, its new value will take affect after the next MCU reset.
The following subsections describe these security-related subjects:
25.5.1
The MCU may be unsecured by using the backdoor key access feature which requires knowledge of the
contents of the backdoor keys (four 16-bit words programmed at addresses 0x7F_FF00–0x7F_FF07). If
the KEYEN[1:0] bits are in the enabled state (see
command (see
keys stored in the Flash memory via the Memory Controller. If the keys presented in the Verify Backdoor
Access Key command match the backdoor keys stored in the Flash memory, the SEC bits in the FSEC
register (see
not permitted as backdoor keys. While the Verify Backdoor Access Key command is active, P-Flash block
0 will not be available for read access and will return invalid data.
The user code stored in the P-Flash memory must have a method of receiving the backdoor keys from an
external stimulus. This external stimulus would typically be through one of the on-chip serial ports.
If the KEYEN[1:0] bits are in the enabled state (see
backdoor key access sequence described below:
The Verify Backdoor Access Key command is monitored by the Memory Controller and an illegal key will
prohibit future use of the Verify Backdoor Access Key command. A reset of the MCU is the only method
to re-enable the Verify Backdoor Access Key command.
After the backdoor keys have been correctly matched, the MCU will be unsecured. After the MCU is
unsecured, the sector containing the Flash security byte can be erased and the Flash security byte can be
reprogrammed to the unsecure state, if desired.
In the unsecure state, the user has full control of the contents of the backdoor keys by programming
addresses 0x7F_FF00–0x7F_FF07 in the Flash configuration field.
The security as defined in the Flash security byte (0x7F_FF0F) is not changed by using the Verify
Backdoor Access Key command sequence. The backdoor keys stored in addresses
0x7F_FF00–0x7F_FF07 are unaffected by the Verify Backdoor Access Key command sequence. After the
next reset of the MCU, the security state of the Flash module is determined by the Flash security byte
952
1. Follow the command sequence for the Verify Backdoor Access Key command as explained in
2. If the Verify Backdoor Access Key command is successful, the MCU is unsecured and the
Unsecuring the MCU using Backdoor Key Access
Unsecuring the MCU in Special Single Chip Mode using BDM
Mode and Security Effects on Flash Command Availability
Section 25.4.2.12
SEC[1:0] bits in the FSEC register are forced to the unsecure state of 10
Unsecuring the MCU using Backdoor Key Access
Table
Section
25-12) will be changed to unsecure the MCU. Key values of 0x0000 and 0xFFFF are
25.4.2.12) allows the user to present four prospective keys for comparison to the
MC9S12XE-Family Reference Manual , Rev. 1.23
Section
Section
25.3.2.2), the Verify Backdoor Access Key
25.3.2.2), the MCU can be unsecured by the
Freescale Semiconductor

Related parts for MC9S12XEP100CAL