MC912DG128AMPVE Freescale Semiconductor, MC912DG128AMPVE Datasheet - Page 339

• Manufacturer Part Number: MC912DG128AMPVE
• Description: IC MCU 128K FLASH 8MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC12r

Specifications of MC912DG128AMPVE

• Core Processor: CPU12
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: CAN, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: HC912D
• Core: HC12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 69
• Number Of Timers: 8
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (8-ch x 10-bit)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18.8.1 msCAN12 SLEEP Mode
MC68HC912DT128A — Rev 4.0
MOTOROLA
The CPU can request the msCAN12 to enter this low-power mode by
asserting the SLPRQ bit in the module configuration register (see
18-6). The time when the msCAN12 will then enter SLEEP mode
depends on its current activity:
The application software must avoid setting up a transmission (by
clearing one or more TXE flag(s)) and immediately request SLEEP
mode (by setting SLPRQ). It will then depend on the exact sequence of
operations whether the msCAN12 will start transmitting or go into
SLEEP mode directly.
During SLEEP mode, the SLPAK flag is set. The application software
should use SLPAK as a handshake indication for the request (SLPRQ) to
go into SLEEP mode. When in SLEEP mode, the msCAN12 stops its
internal clocks. Clocks to allow register accesses will still run. The TxCAN
pin will stay in recessive state. If RXF=1, the message can be read and
RXF can be cleared. However, if the msCAN12 is in bus-off state, it stops
counting 128*11 consecutive recessive bits due to the stopped clocks.
Likewise, copying of RxBG into RxFG will not take place while in sleep
mode. It is possible to access the transmit buffers and to clear the TXE
flags. No message abort will take place while in sleep mode.
The msCAN12 will leave SLEEP mode (wake-up) when
•
•
•
•
•
•
Freescale Semiconductor, Inc.
For More Information On This Product,
If there are one or more message buffers are scheduled for
transmission (TXEx = 0), the msCAN will continue to transmit until
all transmit message buffers are empty (TXEx = 1, transmitted
successfully or aborted) and then goes into Sleep Mode
If it is receiving, it continues to receive and goes into Sleep Mode
as soon as the CAN bus next becomes idle
If it is neither transmitting nor receiving, it will immediately go into
SLEEP mode
bus activity occurs or
the MCU clears the SLPRQ bit or
the MCU sets SFTRES.
Go to: www.freescale.com
MSCAN Controller
MSCAN Controller
Low Power Modes
Technical Data
Figure
339