MC705P6ACDWE Freescale Semiconductor, MC705P6ACDWE Datasheet - Page 57

IC MCU 176 BYTES RAM 28-SOIC

MC705P6ACDWE

Manufacturer Part Number
MC705P6ACDWE
Description
IC MCU 176 BYTES RAM 28-SOIC
Manufacturer
Freescale Semiconductor
Series
HC05r
Datasheet

Specifications of MC705P6ACDWE

Core Processor
HC05
Core Size
8-Bit
Speed
2.1MHz
Connectivity
SIO
Peripherals
POR, WDT
Number Of I /o
21
Program Memory Size
4.5KB (4.5K x 8)
Program Memory Type
OTP
Ram Size
176 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 4x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-SOIC (7.5mm Width)
Processor Series
HC705P
Core
HC05
Data Bus Width
8 bit
Data Ram Size
176 B
Maximum Clock Frequency
2.1 MHz
Number Of Programmable I/os
21
Number Of Timers
1
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
8 bit, 4 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
 Details

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC705P6ACDWE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Part Number:
MC705P6ACDWE
Manufacturer:
FREESCALE
Quantity:
2 200
Part Number:
MC705P6ACDWE
Manufacturer:
FREESCALE
Quantity:
2 200
Part Number:
MC705P6ACDWE
Manufacturer:
MOT
Quantity:
1 000
Part Number:
MC705P6ACDWE
Manufacturer:
MOT
Quantity:
1 000
Part Number:
MC705P6ACDWE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC705P6ACDWE
0
Company:
Part Number:
MC705P6ACDWE
Quantity:
500
Company:
Part Number:
MC705P6ACDWE
Quantity:
466
Chapter 10
EPROM
10.1 Introduction
The user EPROM consists of 48 bytes of user page zero EPROM from $0020 to $004F, 4608 bytes of
user EPROM from $0100 to $12FF, the two MOR reset values located at $1EFF and $1F00, and 16 bytes
of user vectors EPROM from $1FF0 to $1FFF. The bootloader ROM and vectors are located from $1F01
to $1FEF.
10.2 EPROM Erasing
The MC68HC705P6A can be erased by exposure to a high-intensity ultraviolet (UV) light with a
wavelength of 2537 angstroms. The recommended dose (UV intensity multiplied by exposure time) is
15 Ws/cm
positioned about one inch from the UV lamp. An erased EPROM byte will read as $00.
10.3 EPROM Programming Sequence
The bootloader software goes through a complete write cycle of the EPROM including the MOR. This is
followed by a verify cycle which continually branches in a loop if an error is found. A sample routine to
program a byte of EPROM is shown in
10.4 EPROM Registers
Three registers are associated with the EPROM: the EPROM programming register (EPROG) and the
two mask option registers (MOR). The EPROG register controls the actual programming of the EPROM
bytes and the MOR. The MOR registers control the six mask options found on the ROM version of this
MCU (MC68HC05P6), the EPROM security feature, and eight additional port A interrupt options.
10.5 EPROM Programming Register (EPROG)
This register is used to program the EPROM array. Only the ELAT and EPGM bits are available.
Table 10-1
reset. All the bits in the EPROG register are cleared by reset.
Freescale Semiconductor
2
. UV lamps without shortwave filters should be used, and the EPROM device should be
shows the location of each bit in the EPROG register and the state of these bits coming out of
Only parts packaged in a windowed package may be erased. Others are
one-time programmable and may not be erased by UV exposure.
To avoid damage to the MCU, V
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Table
10-1.
DD
NOTE
NOTE
must be applied to the MCU before V
PP
.
57

Related parts for MC705P6ACDWE