MPC562MZP56 Freescale Semiconductor, MPC562MZP56 Datasheet - Page 129

• Manufacturer Part Number: MPC562MZP56
• Description: IC MPU 32BIT 56MHZ PPC 388-PBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC562MZP56

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 56MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 64
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• Processor Series: MPC5xx
• Core: PowerPC
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: SCI, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 22
• Operating Supply Voltage: 2.6 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 32 Channel)
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No

Nexus mode is exited by:
2.6
During reset, a 130-µA (maximum) resistor “weakly pulls” all input signals, with the exception of the
power-supply and clock-related signals, to a value based on conditions described in
“Electrical
CLKOUT, HRESET, and SRESET) are pulled only by the pull-up/pull-down.
2.6.1
The reset configuration word (RCW) defines the post-reset functionality of some multiplexed signals. For
details on these signals and how they are configured, refer to Section 7.5.2, “Hard Reset Configuration
Word.”
The 2.6-V bus related signals have selectable output buffer drive strengths that are controlled by the COM0
bit in the USIU’s system clock and reset control register (SCCR). The control is as follows:
2.6.2
While HRESET is asserted, the reset-configuration value is latched from the data bus into various bits on
the part. The function of many signals depends upon the value latched. If the value on the data bus changes,
then the function of various signals may also change. This is especially true if the reset configuration word
(RCW) comes from the Flash, because the Flash does not drive the RCW until 256 clocks after the start of
Freescale Semiconductor
PORESET/TRST
JCOMP/RSTI
•
•
•
•
TMS/EVTI
Drive JCOMP/RSTI high
Hold JCOMP/RSTI low to reset Nexus port
Hold TMS/EVTI high to disable Nexus mode at least 4 clocks before driving JCOMP/RSTI high
Drive JCOMP/RSTI high
Reset State
MDI0
Characteristics.” In reset state, all I/O signals become inputs, and all outputs (except for
0 = 2.6-V bus signals full drive (50-pF load)
1 = 2.6-V bus signals reduced drive (25-pF load)
Signal Functionality Configuration Out of Reset
Signal State During Reset
Figure 2-6. Debug Mode Selection (Nexus)
MPC561/MPC563 Reference Manual, Rev. 1.2
Enable and
Configure Nexus
Nexus On
Nexus Off
Appendix F,
Signal Descriptions
T
2-31