PIC16F688-E/ST Microchip Technology, PIC16F688-E/ST Datasheet - Page 105
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC16F688-E/ST
Manufacturer Part Number
PIC16F688-E/ST
Description
IC MCU FLASH 4KX14 14TSSOP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F688T-ISL.pdf
(204 pages)
3.PIC16F688T-ISL.pdf
(6 pages)
4.PIC16F688T-ISL.pdf
(4 pages)
5.PIC16F688T-ISL.pdf
(688 pages)
6.PIC16F688-EP.pdf
(174 pages)
Specifications of PIC16F688-E/ST
Program Memory Type
FLASH
Program Memory Size
7KB (4K x 14)
Package / Case
14-TSSOP
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
UART/USART
Peripherals
Brown-out Detect/Reset, POR, WDT
Number Of I /o
12
Eeprom Size
256 x 8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Processor Series
PIC16F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
SCI/USART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
12
Number Of Timers
2
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
Data Rom Size
256 B
Height
0.9 mm
Length
5 mm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2 V
Width
4.4 mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT14SS-1 - SOCKET TRANSITION 14DIP/14SSOPAC162061 - HEADER INTRFC MPLAB ICD2 20PINAC162056 - HEADER INTERFACE ICD2 16F688
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
11.4
The on-chip POR circuit holds the chip in Reset until
V
operation. To take advantage of the POR, simply
connect the MCLR pin through a resistor to V
will eliminate external RC components usually needed
to create Power-on Reset. A maximum rise time for
V
cations” for details. If the BOD is enabled, the maxi-
mum rise time specification does not apply. The BOD
circuitry will keep the device in Reset until V
V
(BOD)”).
When the device starts normal operation (exits the
Reset condition), device operating parameters (i.e.,
voltage, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not met, the
device must be held in Reset until the operating
conditions are met.
For additional information, refer to Application Note
AN607, “Power-up Trouble Shooting” (DS00607).
11.4.1
PIC16F688 has a noise filter in the MCLR Reset path.
The filter will detect and ignore small pulses.
It should be noted that a WDT Reset does not drive
MCLR pin low.
The behavior of the ESD protection on the MCLR pin
has been altered from early devices of this family.
Voltages applied to the pin that exceed its specification
can result in both MCLR Resets and excessive current
beyond the device specification during the ESD event.
For this reason, Microchip recommends that the MCLR
pin no longer be tied directly to V
network, as shown in Figure 11-2, is suggested.
An internal MCLR option is enabled by clearing the
MCLRE bit in the Configuration Word register. When
cleared, MCLR is internally tied to V
weak pull-up is enabled for the MCLR pin. In-Circuit
Serial Programming is not affected by selecting the
internal MCLR option.
2004 Microchip Technology Inc.
DD
DD
BOD
Note:
is required. See Section 14.0 “Electrical Specifi-
has reached a high enough level for proper
(see
Power-On Reset
The POR circuit does not produce an
internal Reset when V
re-enable the POR, V
for a minimum of 100 s.
MCLR
Section 11.4.4
“Brown-Out
DD
DD
. The use of an RC
DD
DD
must reach Vss
and an internal
declines. To
DD
DD
reaches
Detect
. This
Preliminary
FIGURE 11-2:
11.4.2
The on-chip POR circuit holds the chip in Reset until
V
operation. To take advantage of the POR, simply
connect the MCLR pin through a resistor to V
will eliminate external RC components usually needed
to create Power-on Reset. A maximum rise time for
V
cations” for details. If the BOD is enabled, the
maximum rise time specification does not apply. The
BOD circuitry will keep the device in Reset until V
reaches V
Detect (BOD)”).
When the device starts normal operation (exits the
Reset condition), device operating parameters (i.e.,
voltage, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not met, the
device must be held in Reset until the operating
conditions are met.
For additional information, refer to Application Note
AN607, “Power-up Trouble Shooting” (DS00607).
DD
DD
Note:
is required. See Section 14.0 “Electrical Specifi-
has reached a high enough level for proper
V
DD
R1
1 k
BOD
POWER-ON RESET (POR)
The POR circuit does not produce an
internal Reset when V
re-enable the POR, V
for a minimum of 100 s.
C1
0.1 F
(optional, not critical)
or greater)
(see Section 11.4.4 “Brown-Out
RECOMMENDED
CIRCUIT
PIC16F688
MCLR
DD
DS41203B-page 103
PIC16F688
DD
must reach Vss
declines. To
MCLR
DD
. This
DD