PIC18F8410-E/PT Microchip Technology, PIC18F8410-E/PT Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC18F8410-E/PT
Manufacturer Part Number
PIC18F8410-E/PT
Description
IC PIC MCU FLASH 16KX16 80TQFP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC18F6310-IPT.pdf
(412 pages)
2.PIC18F6310-IPT.pdf
(16 pages)
3.PIC18F6310-IPT.pdf
(4 pages)
4.PIC18F6310-IPT.pdf
(28 pages)
5.PIC18F6310-IPT.pdf
(6 pages)
6.PIC18F6310-IPT.pdf
(4 pages)
Specifications of PIC18F8410-E/PT
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
EBI/EMI, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
70
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 12x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
80-TFQFP
For Use With
XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F8410-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC18F6310/6410/8310/8410
2. Module: MSSP
3. Module: MSSP
DS80206F-page 2
When the MSSP is configured for SPI Master
mode, the SDO pin cannot be disabled by setting
the TRISC<5> bit. The SDO pin always outputs
the content of SSPBUF regardless of the state of
the TRIS bit.
In Slave mode with Slave Select enabled,
SSPM3:SSPM0 = 0010 (SSPCON1<3:0>), the
SDO pin can be disabled by placing a logic high
level on the SS pin (RF7).
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
After an I
register may be written for up to 10 T
additional writes are blocked. The data transfer may
be corrupted if SSPBUF is written during this time.
The WCOL bit is set any time an SSPBUF write
occurs during a transfer.
Work around
Avoid writing SSPBUF until the data transfer is
complete, indicated by the setting of the SSPIF bit
(PIR1<3>).
Verify the WCOL bit (SSPCON1<7>) is clear after
writing SSPBUF to ensure any potential transfer in
progress is not corrupted.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C transfer is initiated, the SSPBUF
CY
before
4. Module: MSSP
5. Module: MSSP
In 10-bit Addressing mode, when a Repeated Start
is issued followed by the high address byte and a
write command (R/W = 0), an ACK is not issued.
Work around
There are two work arounds available:
1. Single-Master Environment:
2. Multi-Master Environment:
Date Codes that pertain to this issue:
All engineering and production devices.
I
bit should be set) only when the system is idle
(i.e., when ACKEN, RCEN, PEN, RSEN and SEN
all equal zero). It should not be possible to set the
RCEN bit when the system is not idle, however,
the RCEN bit can be set under this circumstance.
Work around
Wait for the system to become idle before setting the
RCEN bit. This requires a check for the following bits
to be clear:
ACKEN, RCEN, PEN, RSEN and SEN.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C Receive mode should be enabled (i.e., RCEN
In a single-master environment, the user must
issue a Stop, then a Start, followed by a write
to the address high, then the address low
followed by the data.
In a multi-master environment, the user must
issue a Repeated Start, send a dummy write
command to a different address, issue another
Repeated Start and then send a write to the
original address. This procedure will help
maintain control of the bus.
© 2007 Microchip Technology Inc.