TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 223

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

17.1.3 Flash Memory Standby Control (FLSSTB<FSTB>)
IDLE0/1/2, SLEEP0/1/2 or STOP mode, the steady-state current of the flash memory is cut off automatically.
or SLOW1/2 mode, the current can be cut off by the control of the register. To cut off the steady-state current of
the flash memory, set FLSSTB<FSTB> to “1” by the control program in the RAM area. The procedures for
controlling the FLSSTB register are explained below.
write control program executed in the RAM area.)
Low power consumption is enabled by cutting off the steady-state current of the flash memory. In the
When the program is executed in the RAM area (without accessing the flash memory) in the NORMAL 1/2
(Steps1 and 2 are controlled by the program in the flash memory, and steps 3 through 8 are controlled by the
Note 1: The standby function is not operated by setting FLSSTB<FSTB> with the program in the flash memory. You
Note 2: To use the standby function by setting FLSSTB<FSTB> to “1” with the program in the RAM area,
Table 17-1 Flash Memory Access
Serial PROM mode
1. Transfer the control program of the FLSSTB register to the RAM area.
2. Jump to the RAM area.
3. Disable (DI) the interrupt master enable flag (IMF = “0”).
4. Set FLSSTB<FSTB> to “1”.
5. Execute the user program.
6. Repeat step 5 until the return request to the flash memory is detected.
7. Set FLSSTB<FSTB> to “0”.
8. Jump to the flash memory area.
Operating Mode
MCU mode
must set FLSSTB<FSTB> by the program in the RAM area.
FLSSTB<FSTB> must be set to “0” by the program in the RAM area before returning the program control to
the flash memory. If the program control is returned to the flash memory with FLSSTB<FSTB> set to “1”,
the program may misoperate and run out of control.
<BANKSEL>
Don’t care
(BANK0)
(BANK1)
FLSCR
0
1
Page 211
1000H-7FFFH
Access Area
1000H-FFFFH
8000H-FFFFH
Specified Address
9000H-FFFFH
TMP86FS28DFG