TMP86FS28DFG(JZ) Toshiba, TMP86FS28DFG(JZ) Datasheet - Page 243

• Manufacturer Part Number: TMP86FS28DFG(JZ)
• Description: IC MCU 8BIT FLASH 60KB 80-LQFP
• Manufacturer: Toshiba
• Series: TLCS-870/Cr

Specifications of TMP86FS28DFG(JZ)

• Core Processor: 870/C
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: LCD, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Processor Series: TLCS-870
• Core: 870/C
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SIO, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 6
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: BM1040R0A, BMP86A100010A, BMP86A100010B, BMP86A200010B, BMP86A200020A, BMP86A300010A, BMP86A300020A, BMP86A300030A, SW89CN0-ZCC, SW00MN0-ZCC
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• For Use With: BM1401W0A-G - FLASH WRITER ON-BOARD PROGRAMTMP89C900XBG - EMULATION CHIP TMP89F LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: TMP86FS28DFGJZ

Table 18-9 Flash Memory SUM Output Process
BOOT
18.6.3 Flash Memory SUM Output Mode (Operation Command: 90H)
ROM
Note 1: “xxH × 3” indicates that the device enters the halt condition after sending 3 bytes of xxH. For details, refer to " 18.7 Error
Note 2: Refer to " 18.8 Checksum (SUM) ".
1st byte
2nd byte
3rd byte
4th byte
5th byte
6th byte
7th byte
8th byte
9th byte
Table 18-9 shows flash memory SUM output mode process.
Description of the flash memory SUM output mode
Transfer Bytes
Code ".
1. The 1st through 4th bytes of the transmitted and received data contains the same data as in the flash
2. The 5th byte of the received data contains the command data in the flash memory SUM output mode
3. When the 5th byte of the received data contains the operation command data shown in Table 1-6, the
4. The 7th and the 8th bytes contain the upper and lower bits of the checksum, respectively. For how to
5. After sending the checksum, the device waits for the next operation command data.
memory writing mode.
(90H).
device echoes back the value which is the same data in the 6th byte position of the received data (in
this case, 90H). If the 5th byte of the received data does not contain the operation command data, the
device enters the halt condition after transmitting 3 bytes of operation command error code (63H).
calculate the checksum, refer to " 18.8 Checksum (SUM) ".
Matching data (5AH)
-
Baud rate modification data
(See Table 18-4)
-
Operation command data (90H)
-
-
-
(Wait for the next operation com-
mand data)
Transfer Data from External Control-
ler to TMP86FS28DFG
Page 231
9600 bps
9600 bps
9600 bps
9600 bps
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Baud Rate
- (Automatic baud rate adjustment)
OK: Echo back data (5AH)
Error: Nothing transmitted
-
OK: Echo back data
Error: A1H × 3, A3H × 3, 62H × 3 (Note 1)
-
OK: Echo back data (90H)
Error: A1H × 3, A3H × 3, 63H × 3 (Note 1)
OK: SUM (Upper byte) (Note 2)
Error: Nothing transmitted
OK: SUM (Lower byte) (Note 2)
Error: Nothing transmitted
-
Transfer Data from TMP86FS28DFG to
External Controller
TMP86FS28DFG