C8051F930-GQ Silicon Laboratories Inc, C8051F930-GQ Datasheet - Page 191

IC 8051 MCU 64K FLASH 32-LQFP

C8051F930-GQ

Manufacturer Part Number
C8051F930-GQ
Description
IC 8051 MCU 64K FLASH 32-LQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F9xxr
Datasheets

Specifications of C8051F930-GQ

Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
32-LQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
24
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
0.9 V ~ 3.6 V
Data Converters
A/D 23x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F9x
Core
8051
Data Bus Width
8 bit
Data Ram Size
4.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
24
Number Of Timers
4
Operating Supply Voltage
0.9 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F930DK
Minimum Operating Temperature
- 40 C
On-chip Adc
23-ch x 10-bit
No. Of I/o's
24
Ram Memory Size
4KB
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1478 - PLATFORM PROG TOOLSTCK F920,F930336-1477 - PLATFORM PROG TOOLSTCK F920,F930336-1473 - KIT DEV C8051F920,F921,F930,F931336-1472 - BOARD TARGET/PROTO W/C8051F930
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1466

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
C8051F930-GQ
Manufacturer:
SILICON
Quantity:
3 500
Part Number:
C8051F930-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F930-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F930-GQR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
When the RC oscillator is first enabled, the external oscillator valid detector allows software to determine
when oscillation has stabilized. The recommended procedure for starting the RC oscillator is:
19.3.3. External Capacitor Mode
If a capacitor is used as the external oscillator, the circuit should be configured as shown in Figure 19.1,
Option 3. The capacitor should be added to XTAL2, and XTAL2 should be configured for analog I/O with
the digital output drivers disabled. XTAL1 is not affected in RC mode.
The capacitor should be no greater than 100 pF; however, for very small capacitors, the total capacitance
may be dominated by parasitic capacitance in the PCB layout. The oscillation frequency and the required
External Oscillator Frequency Control value (XFCN) in the OSCXCN Register can be determined by the
following equation:
Below is an example of selecting the capacitor and finding the frequency of oscillation Assume V
and f = 150 kHz:
Since a frequency of roughly 150 kHz is desired, select the K Factor from Table 19.2 as KF = 22:
Therefore, the XFCN value to use in this example is 011 and C is approximately 50 pF.
The recommended startup procedure for C mode is the same as RC mode.
0.150 MHz
C
0.150 MHz
f
f
=
where 
f = frequency of clock in MHz
V
=
=
DD
---------------------------------------------- -
0.150 MHz 3.0 V
C
-------------------- -
C V
-------------------- -
C V
1. Configure XTAL2 for analog I/O and disable the digital output drivers.
2. Configure and enable the external oscillator.
3. Poll for XTLVLD > 1.
4. Switch the system clock to the external oscillator.
= power supply voltage in Volts
=
KF
KF
48.8 pF
=
DD
DD
=
22
---------------------- -
C 3.0 V
-----------------
C 3.0
KF
22
R = pull-up resistor value in k 
C = capacitor value on the XTAL2 pin in pF
Rev. 1.1
C8051F93x-C8051F92x
DD
= 3.0 V
191

Related parts for C8051F930-GQ