C8051F930-GQ Silicon Laboratories Inc, C8051F930-GQ Datasheet - Page 25

• Manufacturer Part Number: C8051F930-GQ
• Description: IC 8051 MCU 64K FLASH 32-LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F930-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 24
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 23x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F930DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 23-ch x 10-bit
• No. Of I/o's: 24
• Ram Memory Size: 4KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1478 - PLATFORM PROG TOOLSTCK F920,F930336-1477 - PLATFORM PROG TOOLSTCK F920,F930336-1473 - KIT DEV C8051F920,F921,F930,F931336-1472 - BOARD TARGET/PROTO W/C8051F930
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1466

1.6.
C8051F93x-C8051F92x devices include an on-chip programmable current reference (source or sink) with
two output current settings: low power mode and high current mode. The maximum current output in low
power mode is 63 µA (1 µA steps) and the maximum current output in high current mode is 504 µA (8 µA
steps).
1.7.
C8051F93x-C8051F92x devices include two on-chip programmable voltage comparators: Comparator 0
(CPT0) which is shown in Figure 1.9; Comparator 1 (CPT1) which is shown in Figure 1.10. The two
comparators operate identically but may differ in their ability to be used as reset or wake-up sources. See
Section “18. Reset Sources” on page 180 and the Section “14. Power Management” on page 156 for
details on reset sources and low power mode wake-up sources, respectively.
The Comparator offers programmable response time and hysteresis, an analog input multiplexer, and two
outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0, CP1), or an
asynchronous “raw” output (CP0A, CP1A). The asynchronous CP0A signal is available even when the
system clock is not active. This allows the Comparator to operate and generate an output when the device
is in some low power modes.
The comparator inputs may be connected to Port I/O pins or to other internal signals. Port pins may also be
used to directly sense capacitive touch switches. See Application Note AN338 for details on Capacitive
Touch Switch sensing.
Programmable Current Reference (IREF0)
Comparators
Sensor
Temp
Digital Supply
VDD/DC+
P2.6*
P0.0
VBAT
Figure 1.8. ADC0 Multiplexer Block Diagram
*P1.7-P2. 6 only available as
inputs on 32- pin packages
ADC0MX
AMUX
Rev. 1.1
C8051F93x-C8051F92x
Gain = 0. 5 or 1
Programmable
Attenuator
AIN+
ADC0
25