C8051F930-GQ Silicon Laboratories Inc, C8051F930-GQ Datasheet - Page 272

• Manufacturer Part Number: C8051F930-GQ
• Description: IC 8051 MCU 64K FLASH 32-LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F930-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 24
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 23x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F930DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 23-ch x 10-bit
• No. Of I/o's: 24
• Ram Memory Size: 4KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1478 - PLATFORM PROG TOOLSTCK F920,F930336-1477 - PLATFORM PROG TOOLSTCK F920,F930336-1473 - KIT DEV C8051F920,F921,F930,F931336-1472 - BOARD TARGET/PROTO W/C8051F930
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1466

C8051F93x-C8051F92x
SFR Definition 24.2. SPInCN: SPI Control
SFR Addresses: SPI0CN = 0xF8, Bit-Addressable; SPI1CN = 0xB0, Bit-Addressable 
SFR Pages: SPI0CN = 0x0, SPI1CN = 0x0
272
Name
Reset
Bit
3:2
Type
7
6
5
4
1
0
Bit
NSSnMD[1:0] Slave Select Mode.
RXOVRNn
TXBMTn
WCOLn
MODFn
SPInEN
SPIFn
Name
SPIFn
R/W
7
0
WCOLn MODFn
R/W
6
0
SPIn Interrupt Flag.
This bit is set to logic 1 by hardware at the end of a data transfer. If interrupts are
enabled, setting this bit causes the CPU to vector to the SPIn interrupt service
routine. This bit is not automatically cleared by hardware. It must be cleared by
software.
Write Collision Flag.
This bit is set to logic 1 by hardware (and generates a SPI0 interrupt) to indicate a
write to the SPI0 data register was attempted while a data transfer was in progress.
It must be cleared by software.
Mode Fault Flag.
This bit is set to logic 1 by hardware (and generates a SPI0 interrupt) when a mas-
ter mode collision is detected (NSS is low, MSTEN = 1, and NSSMD[1:0] = 01).
This bit is not automatically cleared by hardware. It must be cleared by software.
Receive Overrun Flag (valid in slave mode only).
This bit is set to logic 1 by hardware (and generates a SPIn interrupt) when the
receive buffer still holds unread data from a previous transfer and the last bit of the
current transfer is shifted into the SPI shift register. This bit is not automatically
cleared by hardware. It must be cleared by software.
Selects between the following NSS operation modes:
(See Section 24.2 and Section 24.3).
00: 3-Wire Slave or 3-Wire Master Mode. NSS signal is not routed to a port pin.
01: 4-Wire Slave or Multi-Master Mode (Default). NSS is an input to the device.
1x: 4-Wire Single-Master Mode. NSS signal is mapped as an output from the
device and will assume the value of NSSMD0.
Transmit Buffer Empty.
This bit will be set to logic 0 when new data has been written to the transmit buffer.
When data in the transmit buffer is transferred to the SPI shift register, this bit will
be set to logic 1, indicating that it is safe to write a new byte to the transmit buffer.
SPIn Enable.
0: SPIn disabled.
1: SPIn enabled.
R/W
5
0
RXOVRNn
R/W
4
0
Rev. 1.1
NSSnMD1
R/W
3
0
Function
NSSnMD0
R/W
2
1
TXBMTn
R
1
1
SPInEN
R/W
0
0