C8051F930-GQ Silicon Laboratories Inc, C8051F930-GQ Datasheet - Page 321

• Manufacturer Part Number: C8051F930-GQ
• Description: IC 8051 MCU 64K FLASH 32-LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F930-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 24
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 23x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F930DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 23-ch x 10-bit
• No. Of I/o's: 24
• Ram Memory Size: 4KB
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1478 - PLATFORM PROG TOOLSTCK F920,F930336-1477 - PLATFORM PROG TOOLSTCK F920,F930336-1473 - KIT DEV C8051F920,F921,F930,F931336-1472 - BOARD TARGET/PROTO W/C8051F930
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1466

C2 Register Definition 27.4. FPCTL: C2 Flash Programming Control
C2 Address: 0x02
C2 Register Definition 27.5. FPDAT: C2 Flash Programming Data
C2 Address: 0xB4
Reset
Reset
Name
Name
Bit
7:0
Bit
7:0
Type
Type
Bit
Bit
FPDAT[7:0] C2 Flash Programming Data Register.
FPCTL[7:0] Flash Programming Control Register.
Name
Name
7
0
7
0
This register is used to pass Flash commands, addresses, and data during C2 Flash
accesses. Valid commands are listed below.
Code
0x06
0x07
0x08
0x03
This register is used to enable Flash programming via the C2 interface. To enable C2
Flash programming, the following codes must be written in order: 0x02, 0x01. Note
that once C2 Flash programming is enabled, a system reset must be issued to
resume normal operation.
0
0
6
6
5
0
5
0
Command
Flash Block Read
Flash Block Write
Flash Page Erase
Device Erase
Rev. 1.1
4
0
4
0
FPCTL[7:0]
FPDAT[7:0]
R/W
R/W
C8051F93x-C8051F92x
Function
Function
3
0
3
0
2
0
2
0
1
0
1
0
0
0
0
0
321