MC912D60CCPVE Freescale Semiconductor, MC912D60CCPVE Datasheet - Page 145

• Manufacturer Part Number: MC912D60CCPVE
• Description: IC MCU 16BIT 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC12r

Specifications of MC912D60CCPVE

• Core Processor: CPU12
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: CAN, MI Bus, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 16x8/10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• Processor Series: HC912D
• Core: HC12
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 86
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.6.2 No Clock at Power-On Reset
MC68HC912D60A — Rev. 3.1
Freescale Semiconductor
CAUTION:
NOTE:
values before the clock loss. All clocks return to their normal settings and
Clock Monitor control is returned to the CME & FCME bits. If AUTO and
BCSP bits were set before the clock loss (selecting the PLL to provide a
system clock) the SYSCLK ramps-up and the PLL locks at the previously
selected frequency. To prevent PLL operation when the external clock
frequency comes back, software should clear the BCSP bit while running
in limp-home mode.
The two shaded regions A and B in
away due to incorrect clocks on SYSCLK if the MCU is clocked by
EXTALi and the PLL is not used.
In region A, there is a delay between the loss of clock and its detection
by the clock monitor. When the EXTALi clock signal is disturbed, the
clock generation circuitry may receive an out of spec signal and drive the
CPU with irregular clocks. This may lead to code runaway.
In region B, as the 13-stage counter is free running, the count of 4096
may be reached when the amplitude of the EXTALi clock has not
stabilized. In this case, an improper EXTALi is sent to the clock
generation circuitry when limp-home mode is exited. This may also
cause code runaway.
If the MCU is clocked by the PLL, the risk of code runaway is very
low, but it can still occur under certain conditions due to irregular
clocks from the clock source appearing on the SYSCLK.
The COP watch dog should always be enabled in order to reset the MCU
in case of a code runaway situation.
It is always advisable to take additional precautions within the
application software to trap such situations.
The voltage level on VDDPLL determines how the MCU responds to an
external clock loss in this case.
With the VDDPLL supply voltage at VDD level, any reset sets the Clock
Monitor Enable bit (CME) and the PLLON bit and clears the NOLHM bit.
Clock Functions
Limp-Home and Fast STOP Recovery modes
Figure 11-3
present a of code run
Clock Functions
Technical Data
145