ZGP323LAH4808C Zilog, ZGP323LAH4808C Datasheet - Page 40
ZGP323LAH4808C
Manufacturer Part Number
ZGP323LAH4808C
Description
IC Z8 GP MCU 8K OTP 48SSOP
Manufacturer
Zilog
Series
Z8® GP™r
Specifications of ZGP323LAH4808C
Core Processor
Z8
Core Size
8-Bit
Speed
8MHz
Peripherals
HLVD, POR, WDT
Number Of I /o
32
Program Memory Size
8KB (8K x 8)
Program Memory Type
OTP
Ram Size
237 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
48-SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Data Converters
-
Connectivity
-
- Current page: 40 of 107
- Download datasheet (3Mb)
PS023709-0208
Caution:
T8_OUT
Counter Enable Command;
T8_OUT Switches to Its
Initial Value (CTR1 D1)
Two successive commands are necessary. First, the counter/timers must be stopped.
Second, the status bits must be reset. These commands are required because it takes one
counter/timer clock interval for the initiated event to actually occur. See
Figure
T8 DEMODULATION Mode
You must program TC8L and TC8H to
(rising, falling, or both depending on CTR1, D5; D4) is detected, it starts to count down.
When a subsequent edge (rising, falling, or both depending on CTR1, D5; D4) is detected
during counting, the current value of T8 is complemented and put into one of the capture
registers. If it is a positive edge, data is put into LO8; if it is a negative edge, data is put
into HI8. From that point, one of the edge detect status bits (CTR1, D1; D0) is set, and an
interrupt can be generated if enabled (CTR0, D2). Meanwhile, T8 is loaded with
starts counting again. If T8 reaches 0, the timeout status bit (CTR0, D5) is set, and an
Counter Enable Command;
T8_OUT Switches to Its
Initial Value (CTR1 D1)
Using the same instructions for stopping the counter/timers and setting the status bits is
not recommended.
20.
TC8L
T8_OUT Toggles
Figure 19. T8_OUT in SINGLE-PASS Mode
Figure 20. T8_OUT in MODULO-N Mode
TC8H
TC8H
Counts
T8_OUT Toggles;
Timeout Interrupt
Timeout
Interrupt
FFH
TC8L
. After T8 is enabled, when the first edge
TC8H
Product Specification
Timeout
Interrupt
Functional Description
Figure 19
TC8L
ZGP323L
FFh
. . .
and
and
36
Related parts for ZGP323LAH4808C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PLATFORM DEV ICE Z8 GP ZGP323
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet: