MC908AZ60ACFU Freescale Semiconductor, MC908AZ60ACFU Datasheet - Page 277

• Manufacturer Part Number: MC908AZ60ACFU
• Description: IC MCU FLASH 8.4MHZ 60K 64QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AZ60ACFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8.4MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 52
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 15x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

During Sleep mode, the SLPAK flag is set. The application software should use SLPAK as a handshake
indication for the request (SLPRQ) to go into Sleep mode. When in Sleep mode, the MSCAN08 stops its
internal clocks. However, clocks to allow register accesses still run. If the MSCAN08 is in buss-off state,
it stops counting the 128*11 consecutive recessive bits due to the stopped clocks. The TxCAN pin stays
in recessive state. If RXF=1, the message can be read and RXF can be cleared. Copying of RxGB into
RxFG doesn’t take place while in Sleep mode. It is possible to access the transmit buffers and to clear
the TXE flags. No message abort takes place while in Sleep mode.
The MSCAN08 leaves Sleep mode (wake-up) when:
After wake-up, the MSCAN08 waits for 11 consecutive recessive bits to synchronize to the bus. As a
consequence, if the MSCAN08 is woken-up by a CAN frame, this frame is not received. The receive
message buffers (RxFG and RxBG) contain messages if they were received before Sleep mode was
entered. All pending actions are executed upon wake-up: copying of RxBG into RxFG, message aborts
and message transmissions. If the MSCAN08 is still in bus-off state after Sleep mode was left, it continues
counting the 128*11 consecutive recessive bits.
23.8.2 MSCAN08 Soft Reset Mode
In Soft Reset mode, the MSCAN08 is stopped. Registers can still be accessed. This mode is used to
initialize the module configuration, bit timing and the CAN message filter. See
Control Register 0
When setting the SFTRES bit, the MSCAN08 immediately stops all ongoing transmissions and
receptions, potentially causing CAN protocol violations.
23.8.3 MSCAN08 Power Down Mode
The MSCAN08 is in Power Down mode when the CPU is in Stop mode.
When entering the Power Down mode, the MSCAN08 immediately stops all ongoing transmissions and
receptions, potentially causing CAN protocol violations.
To protect the CAN bus system from fatal consequences of violations to the above rule, the MSCAN08
drives the TxCAN pin into recessive state.
Freescale Semiconductor
•
•
•
bus activity occurs or
the MCU clears the SLPRQ bit or
the MCU sets the SFTRES bit
The MCU cannot clear the SLPRQ bit before the MSCAN08 is in Sleep
mode (SLPAK=1).
The user is responsible to take care that the MSCAN08 is not active when
Soft Reset mode is entered. The recommended procedure is to bring the
MSCAN08 into Sleep mode before the SFTRES bit is set.
The user is responsible to take care that the MSCAN08 is not active when
Power Down mode is entered. The recommended procedure is to bring the
MSCAN08 into Sleep mode before the STOP instruction is executed.
MC68HC908AZ60A • MC68HC908AS60A • MC68HC908AS60E Data Sheet, Rev. 6
for a complete description of the Soft Reset mode.
NOTE
NOTE
NOTE
23.13.1 MSCAN08 Module
Low Power Modes
277