MC908AZ60ACFU Freescale Semiconductor, MC908AZ60ACFU Datasheet - Page 54

no-image

MC908AZ60ACFU

Manufacturer Part Number
MC908AZ60ACFU
Description
IC MCU FLASH 8.4MHZ 60K 64QFP
Manufacturer
Freescale Semiconductor
Series
HC08r
Datasheet

Specifications of MC908AZ60ACFU

Core Processor
HC08
Core Size
8-Bit
Speed
8.4MHz
Connectivity
CAN, SCI, SPI
Peripherals
LVD, POR, PWM
Number Of I /o
52
Program Memory Size
60KB (60K x 8)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 15x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-QFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC908AZ60ACFU
Manufacturer:
MOTOROLA
Quantity:
84
Part Number:
MC908AZ60ACFU
Manufacturer:
FREESCAL
Quantity:
2 309
Part Number:
MC908AZ60ACFU
Manufacturer:
FREESCALE
Quantity:
400
Part Number:
MC908AZ60ACFU
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC908AZ60ACFU
Manufacturer:
FREESCALE
Quantity:
400
Part Number:
MC908AZ60ACFU
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
MC908AZ60ACFU1L87J
Manufacturer:
MOT
Quantity:
143
Part Number:
MC908AZ60ACFU3K85K
Manufacturer:
FUJI
Quantity:
1 078
Part Number:
MC908AZ60ACFUE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC908AZ60ACFUE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC908AZ60ACFUE
Manufacturer:
FREESCALE
Quantity:
8 908
Part Number:
MC908AZ60ACFUE1L87J
Manufacturer:
TEMIC
Quantity:
350
Part Number:
MC908AZ60ACFUER
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
FLASH-1 Memory
Decreasing the value in FL1BPR by one increases the protected range by one page (128 bytes).
However, programming the block protect register with $FE protects a range twice that size, 256 bytes, in
the corresponding array. $FE means that locations $FF00–$FFFF are protected in FLASH-1.
The FLASH memory does not exist at some locations. The block protection range configuration is
unaffected if FLASH memory does not exist in that range. Refer to the memory map and make sure that
the desired locations are protected.
4.4 FLASH-1 Block Protection
Due to the ability of the on-board charge pump to erase and program the FLASH memory in the target
application, provision is made for protecting blocks of memory from unintentional erase or program
operations due to system malfunction. This protection is done by using the FLASH-1 Block Protection
Register (FL1BPR). FL1BPR determines the range of the FLASH-1 memory which is to be protected. The
range of the protected area starts from a location defined by FL1BPR and ends at the bottom of the
FLASH-1 memory ($FFFF). When the memory is protected, the HVEN bit can not be set in either ERASE
or PROGRAM operations.
When the FLASH-1 Block Protect Register is programmed with all 0’s, the entire memory is protected
from being programmed and erased. When all the bits are erased (all 1’s), the entire memory is accessible
for program and erase.
When bits within FL1BPR are programmed (logic 0), they lock a block of memory address ranges as
shown in
the protected block of FLASH memory can not be erased or programmed.
54
4.3.2 FLASH-1 Block Protect
In performing a program or erase operation, the FLASH-1 Block Protect
Register must be read after setting the PGM or ERASE bit and before
asserting the HVEN bit.
The vector locations and the FLASH Block Protect Registers are located in
the same page. FL1BPR and FL2BPR are not protected with special
hardware or software; therefore, if this page is not protected by FL1BPR
and the vector locations are erased by either a page or a mass erase
operation, both FL1BPR and FL2BPR will also get erased.
MC68HC908AZ60A • MC68HC908AS60A • MC68HC908AS60E Data Sheet, Rev. 6
Register. If FL1BPR is programmed with any value other than $FF,
NOTE
NOTE
Freescale Semiconductor

Related parts for MC908AZ60ACFU