MC908AZ32ACFU Freescale Semiconductor, MC908AZ32ACFU Datasheet - Page 182

• Manufacturer Part Number: MC908AZ32ACFU
• Description: IC MCU 32K FLASH 8.4MHZ 64-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AZ32ACFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 40
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 15x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Serial Peirpheral Interface (SPI)
CPHA — Clock Phase Bit
SPWOM — SPI Wired-OR Mode Bit
SPE — SPI Enable Bit
SPTIE — SPI Transmit Interrupt Enable Bit
17.13.2 SPI Status and Control Register
The SPI status and control register contains flags to signal the following conditions:
The SPI status and control register also contains bits that perform these functions:
182
This read/write bit controls the timing relationship between the serial clock and SPI data. (See
17-4
CPHA bits. When CPHA = 0, the SS pin of the slave SPI module must be set to logic 1 between bytes.
(See
When CPHA = 0 for a slave, the falling edge of SS indicates the beginning of the transmission. This
causes the SPI to leave its idle state and begin driving the MISO pin with the MSB of its data. Once
the transmission begins, no new data is allowed into the shift register from the data register. Therefore,
the slave data register must be loaded with the desired transmit data before the falling edge of SS. Any
data written after the falling edge is stored in the data register and transferred to the shift register at
the current transmission.
When CPHA = 1 for a slave, the first edge of the SPSCK indicates the beginning of the transmission.
The same applies when SS is high for a slave. The MISO pin is held in a high-impedance state, and
the incoming SPSCK is ignored. In certain cases, it may also cause the MODF flag to be set. (See
17.6.2 Mode Fault
machine.
This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO so that those pins
become open-drain outputs.
This read/write bit enables the SPI module. Clearing SPE causes a partial reset of the SPI (see
Resetting the
This read/write bit enables CPU interrupt requests generated by the SPTE bit. SPTE is set when a byte
transfers from the transmit data register to the shift register. Reset clears the SPTIE bit.
•
•
•
•
•
•
•
1 = Wired-OR SPSCK, MOSI, and MISO pins
0 = Normal push-pull SPSCK, MOSI, and MISO pins
1 = SPI module enabled
0 = SPI module disabled
1 = SPTE CPU interrupt requests enabled
0 = SPTE CPU interrupt requests disabled
Receive data register full
Failure to clear SPRF bit before next byte is received (overflow error)
Inconsistent logic level on SS pin (mode fault error)
Transmit data register empty
Enable error interrupts
Enable mode fault error detection
Select master SPI baud rate
and
Figure
Figure
17-11). Reset sets the CPHA bit.
SPI). Reset clears the SPE bit.
17-5.) To transmit data between SPI modules, the SPI modules must have identical
Error). A logic 1 on the SS pin does not in any way affect the state of the SPI state
MC68HC908AZ32A Data Sheet, Rev. 2
Freescale Semiconductor
Figure
17.9