AD622AR Analog Devices Inc, AD622AR Datasheet - Page 12

• Manufacturer Part Number: AD622AR
• Description: IC AMP INST LP 18MA 8SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD622AR

• Slew Rate: 1.2 V/µs
• Rohs Status: RoHS non-compliant
• Amplifier Type: Instrumentation
• Number Of Circuits: 1
• -3db Bandwidth: 1MHz
• Current - Input Bias: 2nA
• Voltage - Input Offset: 60µV
• Current - Supply: 900µA
• Current - Output / Channel: 18mA
• Voltage - Supply, Single/dual (±): ±2.6 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• No. Of Amplifiers: 1
• Bandwidth: 1MHz
• Supply Current: 1.5mA
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Operating Temperature Range: -40°C To +85°C
• Programmable Gain Max: 1000
• Output Type: -
• Gain Bandwidth Product: -
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD622
Figure 18 shows an example where the differential filter
frequency is approximately 400 Hz, and the common-mode
filter frequency is approximately 40 kHz. With this differential
filter in place and operating at gain of 1000, the typical dc offset
shift over a frequency range of 1 Hz to 20 MHz is less than 1.5 μV
RTI, and the RF signal rejection of the circuit is better than
71 dB. At a gain of 100, the dc offset shift is well below 1 mV
RTI, and RF rejection is greater than 70 dB.
The input resistors should be selected to be high enough to
isolate the sensor from the C
enough not to influence system noise. Mismatch between
R × C
degrades the CMRR of the AD622. Therefore, the C
should be high precision types such as NPO/COG ceramics.
The tolerance of the C
GROUND RETURNS FOR INPUT BIAS CURRENTS
Input bias currents are those currents necessary to bias the
input transistors of an amplifier. There must be a direct return
path for these currents; therefore, when amplifying floating
input sources such as transformers or ac-coupled sources, there
must be a dc path from each input to ground as shown in
Figure 19, Figure 20, and Figure 21. Refer to the
Guide to Instrumentation Amplifiers
Inc.) for more information regarding in-amp applications.
C
at the positive input and R × C
D
capacitor is less critical.
C
and C
(free from Analog Devices,
D
C
capacitors but low
at the negative input
Designer’s
C
capacitors
Rev. D | Page 12 of 16
Figure 19. Ground Returns for Bias Currents with Transformer Coupled Inputs
Figure 20. Ground Returns for Bias Currents with Thermocouple Inputs
Figure 21. Ground Returns for Bias Currents with AC-Coupled Inputs
100kΩ
R
R
G
G
100kΩ
+IN
–IN
R
–IN
+IN
G
–IN
+IN
2
1
8
3
2
1
8
3
2
1
8
3
AD622
AD622
–V
–V
AD622
4
4
+V
+V
S
S
7
–V
7
S
4
S
+V
S
7
S
5
5
REF
REF
5
REF
6
6
6
LOAD
LOAD
LOAD
V
V
OUT
TO POWER
SUPPLY
GROUND
OUT
TO POWER
SUPPLY
GROUND
V
OUT
TO POWER
SUPPLY
GROUND