LTC2902-2IGN#TRPBF Linear Technology, LTC2902-2IGN#TRPBF Datasheet - Page 12
![IC MON SUPP QD W/RST&SEL 16-SSOP](/photos/6/59/65965/161-16-ssop_sml.jpg)
LTC2902-2IGN#TRPBF
Manufacturer Part Number
LTC2902-2IGN#TRPBF
Description
IC MON SUPP QD W/RST&SEL 16-SSOP
Manufacturer
Linear Technology
Type
Multi-Voltage Supervisorr
Datasheet
1.LTC2902-1CGNPBF.pdf
(16 pages)
Specifications of LTC2902-2IGN#TRPBF
Number Of Voltages Monitored
4
Output
Push-Pull, Totem Pole
Reset
Active Low
Reset Timeout
5 ms Minimum
Voltage - Threshold
16 Selectable Threshold Combinations
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
LTC2902
particular output is known, output fall time (10% to 90%)
is estimated using:
where R
transistor. The typical performance curve (V
demonstrates that the pull-down current is somewhat
linear versus output voltage. Using the 25 C curve, R
estimated to be approximately 40 . Assuming a 150pF
load capacitance, the fall time is about 13.2ns.
Although the outputs are considered to be “open-drain,”
they do have a weak pull-up capability (see COMPX or RST
Pull-Up Current vs V2 curve). Output rise time (10% to
90%) is estimated using:
where R
The on-resistance as a function of the V2 voltage at room
temperature is estimated using:
with V2 = 3.3V, R
capacitance, the rise time is 86 s. If the output needs to
pull up faster and/or to a higher voltage, a smaller
external pull-up resistor may be used. Using a 10k pull-
up resistor, the rise time is reduced to 3.3 s for a 150pF
load capacitance.
The LTC2902-2 has an active pull-up to V2 on the RST
output. The typical performance curve (RST Pull-Up Cur-
rent vs V2 curve) demonstrates that the pull-up current is
somewhat linear versus the V2 voltage and R
mated to be approximately 625 . A 150pF load capaci-
tance makes the rise time about 206ns.
Selecting the Reset Timing Capacitor
The reset time-out period is adjustable in order to accom-
modate a variety of microprocessor applications. The
reset time-out period, t
capacitor, C
of this capacitor is determined by:
12
t
t
C
R
FALL
RISE
RT
PU
= t
PD
PU
RST
6 10
2.2 • R
2.2 • R
V
is the on-resistance of the internal pull-down
is the on-resistance of the pull-up transistor.
RT
•
2 1
• 217 • 10
, between the CRT pin and ground. The value
–
5
PD
PU
PU
U
• C
• C
is about 260k. Using 150pF for load
LOAD
LOAD
RST
–9
U
, is adjusted by connecting a
W
OL
U
PU
vs I
is esti-
SINK
PD
is
)
with C
millisecond of delay can also be expressed as C
217 (pF/ms).
Leaving the CRT pin unconnected will generate a mini-
mum reset time-out of approximately 50 s. Maximum
reset time-out is limited by the largest available low
leakage capacitor. The accuracy of the time-out period will
be affected by capacitor leakage (the nominal charging
current is 2 A) and capacitor tolerance. A low leakage
ceramic capacitor is recommended.
Tolerance Programming and the RESET Disable
Using the two digital inputs T0 and T1, the user can
program the global supply tolerance for the LTC2902 (5%,
7.5%, 10%, 12.5%). The larger tolerances provide more
headroom by lowering the trip thresholds.
Table 4. Tolerance Programming
Under conventional operation, RST and COMPX will go
low when V
pin can be pulled low, overriding the reset operation and
forcing the RST pin high. This feature is useful when
determining supply margins under processor control since
the reset command will not be invoked. The RDIS pin is
connected to a weak internal pull-up to V
allowing the pin to be left floating if unused.
Ensuring RST Valid for V
When V
drastically reduced. The RST pin may float to undeter-
mined voltages when connected to high impedance (such
as CMOS logic inputs). The addition of a pull-down resis-
tor from RST to ground will provide a path for stray charge
and/or leakage currents. The resistor value should be
small enough to provide effective pull-down without ex-
cessively loading the pull-up circuitry. Too large a value
may not pull down well enough. A 100k resistor from RST
to ground is satisfactory for most applications.
High
High
Low
Low
T0
RT
CC
in Farads and t
is below 1V the RST pull-down capability is
X
is below its threshold. At any time, the RDIS
High
High
Low
Low
T1
RST
CC
in seconds. The C
TOLERANCE (%)
Down to 0V (LTC2902-2)
12.5
7.5
10
5
CC
RT
(10 A typ),
V
value per
REF
1.210
1.178
1.146
1.113
RT
/ms =
(V)
2902f