TC1016-1.8VLTTR Microchip Technology, TC1016-1.8VLTTR Datasheet - Page 9
![IC REG LDO 1.8V 80MA SD SC-70-5](/photos/6/65/66533/mfg_sc-70_sml.jpg)
TC1016-1.8VLTTR
Manufacturer Part Number
TC1016-1.8VLTTR
Description
IC REG LDO 1.8V 80MA SD SC-70-5
Manufacturer
Microchip Technology
Datasheets
1.TC101617EV.pdf
(22 pages)
2.TC1016-3.0VLTTR.pdf
(2 pages)
3.TC1185-5.0VCT713.pdf
(20 pages)
Specifications of TC1016-1.8VLTTR
Regulator Topology
Positive Fixed
Voltage - Output
1.8V
Voltage - Input
2.7 ~ 6 V
Voltage - Dropout (typical)
0.15V @ 80mA
Number Of Regulators
1
Current - Output
80mA (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SC-70-5, SC-88A, SOT-323-5, SOT-353, 5-TSSOP
Primary Input Voltage
6V
Output Voltage Fixed
1.8V
Dropout Voltage Vdo
150mV
No. Of Pins
5
Output Current
80mA
Operating Temperature Range
-40°C To +125°C
Termination Type
SMD
Number Of Outputs
1
Polarity
Positive
Input Voltage Max
6 V
Output Voltage
1.8 V
Output Type
Fixed
Dropout Voltage (max)
300 mV
Line Regulation
0.01 % / V
Load Regulation
0.23 %
Voltage Regulation Accuracy
0.5 %
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
TC10161.8VLTTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TC1016-1.8VLTTR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
4.0
The TC1016 is a precision, fixed-output, linear voltage
regulator. The internal linear pass element is a P-
channel MOSFET. As with all P-channel CMOS LDOs,
there is a body drain diode, with the cathode connected
to V
As shown in Figure 4-1, the output voltage of the LDO
is sensed and divided down internally to reduce
external component count. The internal error amplifier
has a fixed, band gap reference on the inverting input,
with the sensed output voltage on the non-inverting
input. The error amplifier output will pull the gate
voltage down until the inputs of the error amplifier are
equal in order to regulate the output voltage.
By sensing the current in the P-channel MOSFET, the
maximum current delivered to the load is limited to a
typical value of 120 mA, preventing excessive current
from damaging the Printed Circuit Board (PCB) in the
event of a shorted or faulted load.
An internal thermal sensing device is used to monitor
the junction temperature of the LDO. When the sensed
temperature is over the set threshold of 160°C (typ.),
the P-channel MOSFET is turned off. When the
MOSFET is off, the power dissipation internal to the
device is almost zero. The device cools until the
junction temperature is approximately 150°C and the
FIGURE 4-1:
FIGURE 4-2:
© 2005 Microchip Technology Inc.
IN
and the anode connected to V
DETAILED DESCRIPTION
TC1016 Block Diagram.
Typical Application Circuit.
R
SOURCE
1
2
3
SHDN
NC
GND
OUT
(Figure 4-1).
SHDN
Control
Temp.
Over
V
IN
V
1
2
3
REF
SHDN
NC
GND
Feedback Resistors
TC1016
R
Current Limit
1
MOSFET is turned on. If the internal power dissipation
is still high enough for the junction to rise to 160°C, it
will again shut off and cool. The maximum operating
junction temperature of the device is 125°C. Steady-
state operation at or near the 160°C overtemperature
point can lead to permanent damage of the device.
The output voltage (V
entire input operating voltage range (2.7V to 6.0V), as
well as the entire load range (0 mA to 80 mA). The
output voltage is sensed through an internal resistor
divider and compared with a precision internal voltage
reference. Several fixed-output voltages are available
by changing the value of the internal resistor divider.
Figure 4-2 shows a typical application circuit. The reg-
ulator is enabled anytime the shutdown input pin is at
or above V
shutdown input pin is below V
the SHDN feature is not used, tie the SHDN pin directly
to the input supply voltage source. While in shutdown,
the supply current decreases to 0.05 µA (typ.) and the
P-channel MOSFET is turned off.
As shown in Figure 4-2, batteries have internal source
impedance. An input capacitor in used to lower the
input impedance of the LDO. In some applications, high
input impedance can cause the LDO to become
unstable.
compensate for this.
Error Amp
+
-
R
EA
V
2
OUT
V
IN
5
4
C
C
OUT
Adding
IH
Body
Diode
IN
, and shutdown (disabled) anytime the
1 µF Ceramic
1 µF Ceramic
V
OUT
V
IN
more
5
4
OUT
Load
) remains stable over the
input
IL
. For applications where
TC1016
capacitance
DS21666B-page 9
can