LX8582A-00CV Microsemi Analog Mixed Signal Group, LX8582A-00CV Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/4/444/microsemi_analog_mixed_signal_group_sml.jpg)
LX8582A-00CV
Manufacturer Part Number
LX8582A-00CV
Description
IC REG LDO POS 8.5A ADJ TO247
Manufacturer
Microsemi Analog Mixed Signal Group
Datasheet
1.LX8582A-00CP.pdf
(7 pages)
Specifications of LX8582A-00CV
Regulator Topology
Positive Adjustable
Voltage - Output
Adjustable
Voltage - Input
Up to 10V
Voltage - Dropout (typical)
1.1V @ 8.5A
Number Of Regulators
1
Current - Output
8.5A
Current - Limit (min)
8.6A
Operating Temperature
0°C ~ 125°C
Mounting Type
Through Hole
Package / Case
TO-247
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
LX8582A-xx
4
The LX8582A is an easy to use Low-Dropout (LDO) voltage
regulator. It has all of the standard self-protection features expected
of a voltage regulator: short circuit protection, safe operating area
protection and automatic thermal shutdown if the device tempera-
ture rises above approximately 165°C.
Please see the table below for recommended minimum capacitor
values.
tolerance and superior reference stability when measured against
the older pin-compatible regulator types that it replaces.
STABILITY
The output capacitor is part of the regulator’s frequency compen-
sation system. Many types of capacitors are available, with different
capacitance value tolerances, capacitance temperature coefficients,
and equivalent series impedances. For all operating conditions,
connection of a 220µF aluminum electrolytic capacitor or a 47µF
solid tantalum capacitor between the output terminal and ground
will guarantee stable operation.
adjust (ADJ) pin and ground, ripple rejection will be improved
(please see the section entitled
pin bypassing is used, the required output capacitor value increases.
Output capacitor values of 220µF (aluminum) or 47µF (tantalum)
provide for all cases of bypassing the ADJ pin. If an ADJ pin bypass
capacitor is not used, smaller output capacitor values are adequate.
The table below shows recommended minimum capacitance values
for stable operation.
RECOMMENDED CAPACITOR VALUES
In order to ensure good transient response from the power supply
system under rapidly changing current load conditions, designers
generally use several output capacitors connected in parallel. Such
an arrangement serves to minimize the effects of the parasitic
resistance (ESR) and inductance (ESL) that are present in all
capacitors. Cost-effective solutions that sufficiently limit ESR and
ESL effects generally result in total capacitance values in the range
of hundreds to thousands of microfarads, which is more than
adequate to meet regulator output capacitor specifications. Output
capacitance values may be increased without limit.
response characteristics of the regulator in a power system under
changing loads. The effects of different capacitor types and values
on transient response parameters, such as overshoot and under-
shoot, can be quickly compared in order to develop an optimum
solution.
Use of an output capacitor is REQUIRED with the LX8582A.
The regulator offers a more tightly controlled reference voltage
If a bypass capacitor is connected between the output voltage
The circuit shown in Figure 1 can be used to observe the transient
INPUT
10µF
10µF
15µF Tantalum, 100µF Aluminum
47µF Tantalum, 220µF Aluminum
OUTPUT
“RIPPLE
P R O D U C T D A T A B O O K 1 9 9 6 / 1 9 9 7
8 . 5 A L
REJECTION”). When ADJ
P
R O D U C T I O N
O W
A P P L I C A T I O N N O T E S
D
R O P O U T
None
15µF
ADJ
P
O S I T I V E
D
Power Supply
OVERLOAD RECOVERY
Like almost all IC power regulators, the LX8582A is equipped with
Safe Operating Area (SOA) protection. The SOA circuit limits the
regulator's maximum output current to progressively lower values
as the input-to-output voltage difference increases. By limiting the
maximum output current, the SOA circuit keeps the amount of
power that is dissipated in the regulator itself within safe limits for
all values of input-to-output voltage within the operating range of
the regulator. The LX8582A SOA protection system is designed to
be able to supply some output current for all values of input-to-
output voltage, up to the device breakdown voltage.
prevent a power supply system from returning to regulated
operation after removal of an intermittent short circuit at the output
of the regulator. This is a normal mode of operation which can be
seen in most similar products, including older devices such as 7800
series regulators. It is most likely to occur when the power system
input voltage is relatively high and the load impedance is relatively
low.
output voltages are very close to zero. The output voltage closely
follows the rising input voltage, and the input-to-output voltage
difference is small. The SOA circuit therefore permits the regulator
to supply large amounts of current as needed to develop the
designed voltage level at the regulator output. Now consider the
case where the regulator is supplying regulated voltage to a resistive
load under steady state conditions. A moderate input-to-output
voltage appears across the regulator but the voltage difference is
small enough that the SOA circuitry allows sufficient current to flow
through the regulator to develop the designed output voltage across
the load resistance. If the output resistor is short-circuited to ground,
the input-to-output voltage difference across the regulator suddenly
becomes larger by the amount of voltage that had appeared across
the load resistor. The SOA circuit reads the increased input-to-
output voltage, and cuts back the amount of current that it will
permit the regulator to supply to its output terminal. When the short
circuit across the output resistor is removed, all the regulator output
current will again flow through the output resistor. The maximum
current that the regulator can supply to the resistor will be limited
by the SOA circuit, based on the large input-to-output voltage across
the regulator at the time the short circuit is removed from the output.
A T A
Under some conditions, a correctly operating SOA circuit may
When the power system is started “cold”, both the input and
R
S
FIGURE 1 — DYNAMIC INPUT and OUTPUT TEST
E G U L A T O R S
H E E T
IN
LX8582A
ADJ
Star Ground
OUT
Minumum Load
(Larger resistor)
Full Load
(Smaller resistor)
R
Copyright © 1997
10ms
DSON
Rev. 1.1
<< R
1 sec
L
1/97