AXT650124 Panasonic Electric Works, AXT650124 Datasheet - Page 161

• Manufacturer Part Number: AXT650124
• Description: CONN HEADER F4S .4MM 50POS SMD
• Manufacturer: Panasonic Electric Works
• Series: F4Sr

Specifications of AXT650124

• Connector Type: Header, Center Strip Contacts
• Number Of Positions: 50
• Pitch: 0.016" (0.40mm)
• Number Of Rows: 2
• Mounting Type: Surface Mount
• Features: Solder Retention
• Contact Finish: Gold
• Mated Stacking Heights: 1mm
• Height Above Board: 0.033" (0.84mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Contact Finish Thickness: -
• Other names: 255-2399-2

AXJ(1)
4. Series A 2 ports DIP terminal without flange
NOTES
1. Use of a cover is recommended
when using this device in order to
prevent scraps, dust, dirt, etc., from
getting inside the receptacle.
2. Since these products come with
metal retainers, the foot patterns for
two retainers (in the case of 1 port) or
for 4 retainers (in the case of 2 ports)
must be fabricated. (Refer to the
diagram for the recommended PCB
processing.) Furthermore, the
retainers must be soldered to the PCB
to anchor them in place.
3. In the case of automatic soldering,
ensure that the solder bath
temperature is less than 260°C and
that the immersion time does not
exceed 10 seconds.
4. Since excessive force on the
terminals will cause deformation and
the integrity of the soldering will be
lost during reflow soldering, avoid
dropping or rough handling of the
product.
164
Matsushita Electric Works, Ltd.
Power
terminal
(No. 1)
Signal terminals
12.5±0.2
13.2
14.5
11.4
14.2
16.4
Retention fitting (clinching)
Ground terminal
(No. 4)
0.75±0.1
2.0±0.2
2.5±0.2
2.5±0.2
5. This connector has metal shell for
preventing EMI, when designing an
enclosure the followings should be
considered. Guide for plug entrance
should be arranged in order to prevent
distorted insertions. Provide a cover
to reinforce the metal shell portions of
the receptacle.
6. Repeated bending of terminals and
holding parts can result in terminals
breaking.
7. The compatible PCB thickness is
either 0.8mm to 1.2mm or 1.6mm for
the DIP type of mounting.
In regard to the compatible PCB
thickness range from 0.8mm to 1.2mm, it
should be added that the only trouble
when using the connector with a PCB
which is less than 0.8mm thick is that
play may develop between the PCB and
metal retainers. The connector can
therefore be used if it is clamped or some
other measure is taken to secure it.
The same applies when the 1.6mm type
connector is used with a PCB which is
less than 1.6mm thick.
10.28
2.0±0.1
Shell
11.7
5.68
2.71
5.33
Body
2.0±0.1
Contact
Note) Since product bottom is a metal shell, do not
8. Please take care of excessive force
to flange. (Recommended torque
tension: 0.05 to 0.07 N·m)
Tightening too much may deform the
contacts and damage the threads or
screw head. Please be careful.
Regarding general notes, please refer
to page 17.
For other details, please verify with the
product specification sheets.
AXJ112202
AXJ112302
Part no.
make pattern circuits (to prevent shorting).
Recommended PC board pattern
13.14±0.05
13.14±0.05
http://www.mew.co.jp/ac/e/
(TOP VIEW)
Front edge of connector
mm General tolerance: ±0.3
14.2
16.4
3.7
4.3
2.5±0.05
A
2.5±0.05
2.0±0.05
0.8mm to 1.2mm
board thickness
Applicable PC
0.75±0.1
2.0±0.2
2.5±0.2
2.5±0.2
1.6mm