MC68908GZ8MFAE Freescale Semiconductor, MC68908GZ8MFAE Datasheet - Page 249

IC MCU 8BIT 8K FLASH 48-LQFP

MC68908GZ8MFAE

Manufacturer Part Number
MC68908GZ8MFAE
Description
IC MCU 8BIT 8K FLASH 48-LQFP
Manufacturer
Freescale Semiconductor
Series
HC08r
Datasheet

Specifications of MC68908GZ8MFAE

Core Processor
HC08
Core Size
8-Bit
Speed
8MHz
Connectivity
CAN, LIN, SCI, SPI
Peripherals
LVD, POR, PWM
Number Of I /o
37
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
48-LQFP
Processor Series
M689xx
Core
HC08
Data Bus Width
8 bit
Data Ram Size
1 KB
Interface Type
SPI, SCI, CAN
Maximum Clock Frequency
8 MHz
Number Of Programmable I/os
37
Number Of Timers
2
Operating Supply Voltage
5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Development Tools By Supplier
FSICEBASE, M68CBL05AE, DEMO908GZ60E, M68EML08GZE
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 16 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
 Details
SPRF — SPI Receiver Full Bit
ERRIE — Error Interrupt Enable Bit
OVRF — Overflow Bit
MODF — Mode Fault Bit
SPTE — SPI Transmitter Empty Bit
Freescale Semiconductor
This clearable, read-only flag is set each time a byte transfers from the shift register to the receive data
register. SPRF generates a CPU interrupt request if the SPRIE bit in the SPI control register is set also.
During an SPRF CPU interrupt, the CPU clears SPRF by reading the SPI status and control register
with SPRF set and then reading the SPI data register.
Reset clears the SPRF bit.
This read/write bit enables the MODF and OVRF bits to generate CPU interrupt requests. Reset clears
the ERRIE bit.
This clearable, read-only flag is set if software does not read the byte in the receive data register before
the next full byte enters the shift register. In an overflow condition, the byte already in the receive data
register is unaffected, and the byte that shifted in last is lost. Clear the OVRF bit by reading the SPI
status and control register with OVRF set and then reading the receive data register. Reset clears the
OVRF bit.
This clearable, read-only flag is set in a slave SPI if the SS pin goes high during a transmission with
the MODFEN bit set. In a master SPI, the MODF flag is set if the SS pin goes low at any time with the
MODFEN bit set. Clear the MODF bit by reading the SPI status and control register (SPSCR) with
MODF set and then writing to the SPI control register (SPCR). Reset clears the MODF bit.
This clearable, read-only flag is set each time the transmit data register transfers a byte into the shift
register. SPTE generates an SPTE CPU interrupt request or an SPTE DMA service request if the
SPTIE bit in the SPI control register is set also.
During an SPTE CPU interrupt, the CPU clears the SPTE bit by writing to the transmit data register.
Reset sets the SPTE bit.
1 = Receive data register full
0 = Receive data register not full
1 = MODF and OVRF can generate CPU interrupt requests
0 = MODF and OVRF cannot generate CPU interrupt requests
1 = Overflow
0 = No overflow
1 = SS pin at inappropriate logic level
0 = SS pin at appropriate logic level
1 = Transmit data register empty
0 = Transmit data register not empty
Address: $0011
Do not write to the SPI data register unless the SPTE bit is high.
Reset:
Read:
Write:
Figure 17-15. SPI Status and Control Register (SPSCR)
SPRF
Bit 7
0
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
= Unimplemented
ERRIE
6
0
OVRF
5
0
NOTE
MODF
4
0
SPTE
3
1
MODFEN
2
0
SPR1
1
0
SPR0
Bit 0
0
I/O Registers
249

Related parts for MC68908GZ8MFAE