XR16M2550IL32-F Exar Corporation, XR16M2550IL32-F Datasheet - Page 18

• Manufacturer Part Number: XR16M2550IL32-F
• Description: IC UART FIFO 16B 1.8V DUAL 32QFN
• Manufacturer: Exar Corporation
• Type: Dual UART with 16-byte FIFOsr

Specifications of XR16M2550IL32-F

• Number Of Channels: 2, DUART
• Package / Case: 32-VFQFN Exposed Pad
• Features: *
• Fifo's: 16 Byte
• Voltage - Supply: 2.25 V ~ 3.6 V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Data Rate: 16 Mbps
• Supply Voltage (max): 3.63 V
• Supply Voltage (min): 1.62 V
• Supply Current: 0.5 mA to 2 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 45 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 1.62 V to 3.63 V
• No. Of Channels: 2
• Uart Features: Two Independent UART Channels, Device Identification & Revision
• Supply Voltage Range: 1.62V To 3.63V
• Operating Temperature Range: -40°C To +85°C
• Rohs Compliant: Yes
• Digital Ic Case Style: QFN
• No. Of Pins: 32
• Filter Terminals: SMD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1285

XR16M2550
HIGH PERFORMANCE LOW VOLTAGE DUART WITH 16-BYTE FIFO
The M2550 UART includes the infrared encoder and decoder compatible to the IrDA (Infrared Data
Association) version 1.0. The IrDA 1.0 standard that stipulates the infrared encoder sends out a 3/16 of a bit
wide HIGH-pulse for each “0” bit in the transmit data stream. This signal encoding reduces the on-time of the
infrared LED, hence reduces the power consumption. See
The infrared encoder and decoder are enabled by setting MCR register bit-6 to a ‘1’. When the infrared feature
is enabled, the transmit data output, TX, idles at logic zero level. Likewise, the RX input assumes an idle level
of logic zero from a reset and power up, see
Typically, the wireless infrared decoder receives the input pulse from the infrared sensing diode on the RX pin.
Each time it senses a light pulse, it returns a logic 1 to the data bit stream. However, this is not true with some
infrared modules on the market which indicate a logic 0 by a light pulse. So the M2550 has a provision to invert
the input polarity to accommodate this. In this case user can enable MCR bit-2 to invert the input signal.
2.17
Infrared Mode
F
IGURE
Receive
IR Pulse
(RX pin)
RX Data
TX Data
Transmit
IR Pulse
(TX Pin)
11. I
NFRARED
0
Bit Time
Bit Time
0
1
1/16 Clock Delay
T
RANSMIT
1
0
Figure
0
1
Character
Data Bits
D
11.
1
ATA
0
18
3/16 Bit Time
Data Bits
Character
0
E
0
Figure 11
NCODING AND
0
1
1 1
1
below.
0
R
0
ECEIVE
1/2 Bit Time
1
1
IRdecoder-
IrEncoder-1
D
ATA
D
ECODING
REV. 1.0.2