TEF6730HW/V1,557 NXP Semiconductors, TEF6730HW/V1,557 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TEF6730HW/V1,557
Manufacturer Part Number
TEF6730HW/V1,557
Description
IC DIGITAL IF FRONT END 64HTQFP
Manufacturer
NXP Semiconductors
Specifications of TEF6730HW/V1,557
Package / Case
64-TQFP Exposed Pad, 64-eTQFP, 64-HTQFP, 64-VQFP
Modulation Or Protocol
AM, FM, WB
Applications
AM/FM Radio Receiver
Current - Receiving
85.3mA, 114.7mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Voltage - Supply
8 V ~ 9 V
Operating Temperature
-40°C ~ 85°C
Bus Type
I2C
Maximum Agc
14 dB
Maximum Frequency
288 MHz, 108 MHz
Minimum Frequency
144 MHz, 65 MHz
Modulation Technique
AM, FM
Mounting Style
SMD/SMT
Function
Radio
Noise Figure
12.9 dB, 6.9 dB
Operating Supply Voltage
8.5 V
Supply Voltage (min)
8 V
Supply Voltage (max)
9 V
Minimum Operating Temperature
- 40 C
Maximum Operating Temperature
+ 85 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Frequency
-
Sensitivity
-
Memory Size
-
Data Rate - Maximum
-
Lead Free Status / Rohs Status
Compliant
Other names
935278526557
TEF6730HW/V1
TEF6730HW/V1
TEF6730HW/V1
TEF6730HW/V1
Philips Semiconductors
TEF6721HL_4
Product data sheet
8.2.6 Write mode: data byte 4
Table 15:
Table 16:
[1]
Table 17:
Table 18:
Table 19:
BND1
0
0
1
1
BND1
0
1
Bit
7
6 and 5
4
3
2
1
0
AGC1
0
0
1
1
KAGC
X = don’t care.
7
FM band selection bits
AM band selection bits
Format of data byte 4
Description of data byte 4 bits
Setting of wideband AGC for AM (m = 0.3)
BND0
0
1
0
1
BND0
X
X
Symbol
KAGC
AGC[1:0]
LODX
FMINJ
-
AGCSW
MIXGAIN
AGC1
6
Rev. 04 — 20 December 2005
Frequency band
FM standard
FM Japan
FM East Europe
FM weather
Frequency band
AM SW
AM LW/MW
Description
Keyed FM AGC. If KAGC = 0, then keyed FM AGC is off. If KAGC = 1,
then keyed FM AGC is on.
Wideband AGC. These 2 bits set the start value of wideband AGC. For
AM, see
Local or distance. If LODX = 0, then distance mode is on. If LODX = 1,
then local mode is on.
FM mixer image rejection. If FMINJ = 0, then low injection. If
FMINJ = 1, then high injection.
This bit is not used and should be set to logic 0.
AGC switch. If AGCSW = 0, then AM AGC in FM mode and FM AGC in
AM mode is off. If AGCSW = 1, then AM AGC PIN diode drive is active in
FM mode and FM AGC PIN diode drive is active in AM mode.
FM mixer gain. If MIXGAIN = 0, then the FM mixer gain is nominal. If
MIXGAIN = 1, then the FM mixer gain is +6 dB.
AGC0
0
1
0
1
AGC0
5
Table 19
[1]
LODX
4
and for FM, see
VCO divider
2
3
3
1
VCO divider
10
20
AM mixer input voltage (peak value) (mV)
275
375
500
625
FMINJ
Car radio tuner front-end for digital IF
3
Table
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
20.
2
-
TEF6721HL
Charge pump current
130 A + 3 mA
130 A + 3 mA
1 mA
300 A
Charge pump current
1 mA
1 mA
AGCSW
1
MIXGAIN
14 of 48
0