AT86RF211SAH-R Atmel, AT86RF211SAH-R Datasheet - Page 54
![IC RF TXRX FSK 400-950MHZ 48TQFP](/photos/14/22/142249/453-48-tqfp_sml.jpg)
AT86RF211SAH-R
Manufacturer Part Number
AT86RF211SAH-R
Description
IC RF TXRX FSK 400-950MHZ 48TQFP
Manufacturer
Atmel
Datasheet
1.AT86RF211SDK.pdf
(66 pages)
Specifications of AT86RF211SAH-R
Frequency
400MHz ~ 950MHz
Data Rate - Maximum
100kbps
Modulation Or Protocol
FSK
Applications
ISM
Power - Output
7dBm ~ 12dBm
Sensitivity
-107dBm
Voltage - Supply
2.4 V ~ 3.6 V
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TQFP Exposed Pad, 48-eTQFP, 48-HTQFP, 48-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Memory Size
-
Current - Transmitting
-
Current - Receiving
-
Table 3-4.
Note:
Table 3-5.
54
Name
tr = tf
F
T
tw
tsd
thd
tpd
tpzon
tdle
twhle
tpzd
C
Parameter
Frequency range
Frequency range
Crystal frequency
Crystal frequency
Crystal frequency
Crystal load impedance
XTO settling time
XTO settling time
Clock signal P-P voltage
Lock time
Lock time
Rx to Tx toggle time
Phase noise at 10 kHz
L
(1)
These timings refer to Figure 2-32 on page 37.
(2)
(2)(3)
AT86RF211S
Parameter
CMOS rise/fall times
SCK frequency
SCK period
SCK low or high time
SDATA setup before SCK rising
SDATA hold after SCK rising
SDATA output propagation delay after SCK falling
(read mode) (C
Delay to switch SDATA to output after SCK falling
(read mode)
Minimum delay between an edge of SLE and an
edge of SCK
Minimum delay between two accesses to the
registers
Delay to switch SDATA to input (tri-state) after SLE
rising (read mode)
Max load for CMOS output pins
Timings
Synthesizer Specification (unless otherwise specified, data is given for T = 25°C, V
(2)
L
= 30 pF)
10.235
20.490
20.925
400
800
Min
10
5
-82/-76
10.245
20.500
20.945
700
300
150
30
30
8
Conditions
C
L
= 50 pF; 20 – 80%
10.255
20.510
20.965
Max
480
950
20
dBc/Hz
MHz
MHz
MHz
MHz
MHz
Unit
mV
ms
ms
pF
µs
µs
µs
Min
0
200
60
40
40
2
3
40
100
Comment
Digital programming
Digital programming
With IF1 = 10.7 MHz
With IF1 = 10.7 MHz
With IF1 = 21.4 MHz
Parallel mode
Depending on crystal
specification, with R = 3.3 kΩ
If R = 3.3 kΩ not connected
Steady state
From oscillator settling to Fc
±10 kHz
For a 100 kHz shift, ±10 kHz
For a 100 kHz shift, ±10 kHz
434/868 or 915 MHz
SUPPLY
Typ
= 2.7V)
Max
30
5
50
50
40
50
5348B–WIRE–03/06
(1)
(1)
(1)
)
)
Units
ns
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
pF