025-0585-000 ITT Cannon, 025-0585-000 Datasheet - Page 112
025-0585-000
Manufacturer Part Number
025-0585-000
Description
RP DPD 33 & 34 DUST CAP
Manufacturer
ITT Cannon
Datasheet
1.025-0767-001.pdf
(120 pages)
Specifications of 025-0585-000
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
I025-0585-000
- Current page: 112 of 120
- Download datasheet (3Mb)
ITT Cannon recommends resistance soldering for all
solder contacts, particularly for RF cable where
excessive heat will damage the dielectric. Wires
should be pre-tinned. Shells, bushings, endbells and
junction shells Jwhere applicable) must be slipped
over wire bundles before soldering or crimping is
started. The mechanical steps in wiring coaxials are
described below.
Straight
R Coax
90 angle
R Coax
Single Gang - DPD/DPDMA
The DPD/DPDMA can be engaged by means of a
No. 10-32 steel jack screw and clinch nut. This
coupling device is designed to fasten connectors
securely when they are used in other than standard
rack/ panel applications. The jack screws and clinch
nuts are mounted on the shell flanges at the factory.
They may be called out on either -33 or -34 shelis,
although it is preferred to have jack screws on the
-33 shell and the clinch nuts on the -34 shell. The
device can be ordered on both DPD and DPDMA.
Engaging Devices
The suffix "N" or "S" is placed immediately after the mounting
hole variation; i.e., - 1AN, -1AS, etc.
Engaging Device
How to Order
DPD-**-34*-1* N
Two Gang - DPD2/DPD2MA
The DPD2 is engaged by means of a variety of
screw mechanisms. Engaging devices are inter-
changeable (within the thread group) with male or
female mounting on either 33 or 34 shells. The
accompanying tabulation lists the available engag-
ing devices, male opposite female, with which they
mate.
How to Order
Stripping Instructions
DPD/DPDMA
Coax Type
Cable Size
RG-7/U
RG-59/U
RG-62/U
RG-7/U
RG-58/U
RG-59/U
RG-62/U
N = Clinch Nut
S = Jack Screw
.171 (4.34)
.171 (4.34)
.171 (4.34)
.218 (5.54)
.218 (5.54)
.218 (5.54)
.218 (5.54)
A
DPD2
.421 (10.69)
.546 (13.87)
.543 (13.87)
.312 (7.92)
.531 (13.49)
.531 (13.49)
.531 (13.49)
Trim
B
-72C2
DPD-**-33*-1* S
.515 (13.08)
.671 (17.04)
.671 (17.04)
.437 (11.10)
.593 (15.06)
.593 (15.06)
.593 (15.06)
-34PCM
C
1. Cut cable even. Trim to dimensions shown on
tabulation. Care should be taken not to injure
the conductor or dielectric.
3. Remove solder pot cover. Insert cable and solder
conductor to contact. If a straight contact is
used, the dielectric should but against contact
solder pot.
R Coaxial (Straight and 90 )
Number
M
MA
CM
CMRA
DM
DM-1
DM-2
DM-3
DM-7
Part
#10-32
clinch nut
on horizontal
center line
MALE ENGAGING DEVICES
COVER
BRAID
Used On
DPD2MA
DPD2
-34
Shell
112
B
C
A
DIELECTRIC
CONDUCTOR
#10-32 steel jack screw (on horizontal center line)
F
2. Comb braid, tin conductor and remove flux. If a
90 contact is used, bend conductor 90˚ after
tinning.
4. Replace solder pot cover and solder braid to
ferrule.
Specifications and dimensions subject to change
FEMALE ENGAGING DEVICES
Straight
-33
Shell
CF
Dimensions shown in inch (mm)
www.ittcannon.com
1/4 hex with
screwdriver
slot &
safety wire
hole
90
DF
Related parts for 025-0585-000
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
025/040 III 135POS CAP ASSY H
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
025 LOW PROFILE 24POS CAP ASSY
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
ANALOG PANEL METER MODEL TV3 RANGE 0-500MAAC SCALE DUAL 0-700/350AAC
Manufacturer:
NEWARK SERVICES
Part Number:
Description:
025 LP HDF STRAIN RELIEF
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
EMI SHIELDED ENDBELL WITH 4-40 EXTENDED JACKSCREW
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 1.8MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 2.5MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 3.5MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
PLUG STR CRIMP SMB RG174/U 316/U
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI TNM RECP M FLG SEAL 0-12
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
CONN RCPT 6POS JAM NUT W/SCKT
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI R E/B STR C/C SEAL SZ 18
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
CAB CON 16S PIN 18/16 F80 SILVER
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI CON SKT 16-18 TIN ST/LO
Manufacturer:
ITT Cannon
Datasheet: