025-0585-000 ITT Cannon, 025-0585-000 Datasheet - Page 35
025-0585-000
Manufacturer Part Number
025-0585-000
Description
RP DPD 33 & 34 DUST CAP
Manufacturer
ITT Cannon
Datasheet
1.025-0767-001.pdf
(120 pages)
Specifications of 025-0585-000
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
I025-0585-000
- Current page: 35 of 120
- Download datasheet (3Mb)
1. Use basic tool M22520/5-01 with Y-211 die
2. Use extraction tool No. CET-C8. An insertion tool
3. Center contact, rear insulator, crimp ring, support
Installation Data
(#995-0002-249) for crimping.
is not requried (See Note 5).
bushing (not applicable to RG58/RG142 coax-
ials), seal sleeve, front insulator, shell and ferrule
are shipped unassembled in a common container.
Coaxial Contact Data
www.ittcannon.com
MIL-C-81659
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
Without Seal
Socket
Pin
4. Cable Assembly Instructions
A.
B.
C.
A.
B.
C.
A.
B.
C.
Step 1 - If applicable determine which portion of
seal sleeve should be used. If Seal 2 is used, cut
off Seal 1 portion.
Step 2 - In sequence, place seal sleeve, support
bushing and crimp ring over cable jacket.
Step 3 - Trim cable per illustration.
Step 4 - Comb out braid and flare out ends to
permit entry of ferrule.
Step 5 - Complete termination per illustration.
Push ferrule under braid as far as it will go. Trim off braid extending beyond shoulder of ferrule, if necessary.
While holding ferrule in place pull crimp sleeve forward over braid untill it is tight against shoulder on ferrrule. Pull firmly
against face of ferrule to make sure it is up tight.
Trim dielectric to the .035 (0.89)/.030 (0.76) dimension.
Place front insulator over contact and then push assembly into coaxial shell.
Place parts in jaw of crimp tool. Locate jaws at start of chamber on crimp sleeve. Press sleeve firmly into coaxial shell and
crimp.
After assembled coaxial is inserted into connector, push suppurt bushing into grommet until shoulder rests on tubular
extension. Then pull sealing sleeve forward until it is snug on grommet.
Carefully push inner conductor through rear insulator.
While holding rear insulator firmly against ferrule, trim conductor to .156 (3.96)/.146 (3.91) dimension.
Place contact over conductor and solder.
35
APPROX.
(8.89)
.350
SEAL 1
SEAL 2
BUSHING
SEAL
.035 (0.89)
.030 (0.76)
FERRULE
CRIMP AREA
5. To extract coaxial, push back seal sleeve and
6. To facilitate extraction of contacts, the length of
support bushing. Slip cable into extraction tool
Push tool into insert until contacts coaxial retain-
ing shoulder. Grip both cable and tool with one
hand and pull coaxial rearward out of insert
cavity.
free cable adjacent to the rear surface of the
connector should not be less than 2.000 (50.80).
DPXNA/DPXNE
Sealed
.156 (3.96)
.146 (3.71)
REAR INSULATOR
BUSHING
FRONT INSULATOR
CONTACT
COAXIAL SHELL
BRAID
Related parts for 025-0585-000
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
025/040 III 135POS CAP ASSY H
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
025 LOW PROFILE 24POS CAP ASSY
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
ANALOG PANEL METER MODEL TV3 RANGE 0-500MAAC SCALE DUAL 0-700/350AAC
Manufacturer:
NEWARK SERVICES
Part Number:
Description:
025 LP HDF STRAIN RELIEF
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
EMI SHIELDED ENDBELL WITH 4-40 EXTENDED JACKSCREW
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 1.8MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 2.5MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
UNIVERSAL CONTACT 3.5MM SMD
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
PLUG STR CRIMP SMB RG174/U 316/U
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI TNM RECP M FLG SEAL 0-12
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
CONN RCPT 6POS JAM NUT W/SCKT
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI R E/B STR C/C SEAL SZ 18
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
CAB CON 16S PIN 18/16 F80 SILVER
Manufacturer:
ITT Cannon
Datasheet:
Part Number:
Description:
TRI CON SKT 16-18 TIN ST/LO
Manufacturer:
ITT Cannon
Datasheet: