NCP18XH103F0SRB Murata, NCP18XH103F0SRB Datasheet - Page 28
![Thermistors - NTC 0603 10Kohms 3380K](/photos/16/24/162463/nthcp03_sml.jpg)
NCP18XH103F0SRB
Manufacturer Part Number
NCP18XH103F0SRB
Description
Thermistors - NTC 0603 10Kohms 3380K
Manufacturer
Murata
Type
NTCr
Datasheet
1.NCP15WF104J03RC.pdf
(47 pages)
Specifications of NCP18XH103F0SRB
Resistance
10 KOhms
Tolerance
1 %
Termination Style
SMD/SMT
Package / Case
0603
Operating Temperature Range
- 40 C to + 125 C
Power Rating
100 mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NCP18XH103F0SRB
Manufacturer:
MURATA
Quantity:
240 000
Part Number:
NCP18XH103F0SRB
Manufacturer:
MURATA/村田
Quantity:
20 000
5
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
26
No.
10
* · R25 is zero-power resistance at 25 C.
Temperature Sensor Thermo String Type Specifications and Test Methods
1
2
3
4
5
6
7
8
9
· B25/50 is calculated by zero-power resistance of Thermistor in 25 C -50 C.
· After each test, NTC Thermistor should be kept for 1 hour at room temperature (normal humidity and normal atmospheric pressure).
High Temperature
Storage Test
Low Temperature
Storage Test
Humidity
Storage Test
Temperature
Cycle
High Temperature
Load
Insulation Break -
down Voltage
Resistance to
Soldering Heat
Solderability
Lead Wire
Pull Strength
Lead Wire
Bending Strength
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
· Resistance (R25 C) fluctuation rate: less than 1%.
· B-Constant (B25/50 C) fluctuation rate: less than 1%.
· Resistance (R25 C) fluctuation rate: less than 2%.
· B-Constant (B25/50 C) fluctuation rate: less than 1%.
· No damage electrical characteristics at DC100 V, 1 min.
· Resistance (R25 C) fluctuation rate: less than 1%.
· B-Constant (B25/50 C) fluctuation rate: less than 1%.
More than 90% of lead wire surface shall be covered by solder.
· Resistance (R25 C) fluctuation rate: less than 1%.
· B-Constant (B25/50 C) fluctuation rate: less than 1%.
· Lead wire does not break.
Specifications
125 2 C in air, for 1000 +48/-0 hours without loading.
-40 +0/-3 C in air, for 1000 +48/-0 hours without loading.
60 2 C, 90 to 95%RH in air, for 1000 +48/-0 hours without
loading.
-40 +0/-3 C, 30 minutes in air
+25 2 C, 10 to 15 minutes in air
+125 2 C, 30 minutes in air
+ 25 +2/-0 C, 10 to 15 minutes in air (1 cycle)
Continuous 100 cycles, without loading.
85 2 C in air, with 'Operating Current for Sensor' for 1000
+48/-0 hrs.
2mm length of coating resin from the top of Thermistor is to be
dipped into beads of lead (Pb), and DC100V 1 minute is
applied to circuit between beads of lead (Pb) and lead wire.
Both lead wires are dipped into 350 10 C solder for 3.5 0.5
seconds, or 260 5 C solder for 10 1 seconds according to
Fig-1 (solder <JIS Z 3282 H60A>).
Both lead wires are dipped into flux (25wt% colophony <JIS K
5902> isopropyl alcohol <JIS K 8839>) for 5 to 10 seconds.
Then both lead wires are dipped into 235 5 C solder
<JIS Z 3282 H60A> for 2 0.5 seconds according to Fig-1.
The lead wire shall be inserted in a ø1.0mm hole until resin part
contacts with a substrate as shown in fig.-2, and 1N force for 10
seconds shall be applied to the lead wire.
Hold the lead wires as in Fig-3. Bend by 90 degrees and again
bend back to the initial position. Then bend to the other side by
90 degrees and again bend back to the initial position. After
bending process, 10N force for 3 seconds shall be applied to
the lead wire.
Test Methods
1N (10 sec.)
10N (3 sec.)
Solder
Fig-1
Fig-2
Fig-3
Continued on the following page.
1 to 2mm
R44E.pdf
11.2.21